The Legatia X6 is a cone-type driver consisting of an optional proprietary hybrid paper or carbon fiber diaphragm with extremely low moving mass. Paper is widely acknowledged as the best-damping material, as it provides the near optimum balance of strength and weight.
The cone designs offer a wide dispersion pattern to make for flexible installation and speaker location. The Legatia X6 has an outstanding extended frequency response; the usable frequency range of this driver exceeds seven complete octaves of usable bandwidth on-axis (~70 Hz – ~10,000 Hz, depending on cone and phase plug/dust cap topology). Even off-axis, the X6 faithfully recreates more than six full octaves of information, for the ultimate “small-format” midrange/full-range driver.
The X6 uses a copper shorting cup. The shorting cup consists of an optimally sized and plated copper (Cu) cup to create a total inductance profile that is not just low but flat over stroke, frequency, and power. Inductance is the number one limiter of high-frequency extension and modulation of inductance with stroke, frequency, and power, and is the primary source of intermodulation distortion (IMD).
The tinsel leads for the X6 are terminated on one side of the voice coil. The tinsel leads are stitched into the spider and bonded directly to the former and brought out to the terminals, which completely eliminates tinsel lead slap and does not compromise the structural integrity of the cone.
The Legatia X6 comes equipped with heavy-duty nickel-plated spring-loaded push terminals for both positive and negative. The terminals optimize contact and give the end user flexibility in tinned wire or binding post terminations.
The Legatia X6 is the ideal multi-purpose super high-end speaker driver. Mechanical and electrical parameters are amenable to a variety of different installations and speaker locations. This driver is intended to be used in an infinite baffle configuration; a simple, solid baffle, solidly attached to the car’s chassis with available airspace at the rear of the baffle is all that is required for optimum operation. The size of the X6 allows it to be mounted in typical “6-inch” midbass locations within a vehicle, or in custom locations at the discretion of the end-user, as long as there is adequate airspace behind the driver to allow it to maintain proper damping and acoustic suspension.
At home in virtually any arrangement, the X6 is Hybrid Audio Technologies Legatia X high-end large-format midrange/midbass offering, boasting exceptional performance and a design philosophy that goes hand in hand with true high-fidelity playback.
The Legatia X6 is a cone-type driver consisting of an optional proprietary hybrid paper or carbon fiber diaphragm with extremely low moving mass. Paper is widely acknowledged as the best-damping material, as it provides the near optimum balance of strength and weight.
The cone designs offer a wide dispersion pattern to make for flexible installation and speaker location. The Legatia X6 has an outstanding extended frequency response; the usable frequency range of this driver exceeds seven complete octaves of usable bandwidth on-axis (~70 Hz – ~10,000 Hz, depending on cone and phase plug/dust cap topology). Even off-axis, the X6 faithfully recreates more than six full octaves of information, for the ultimate “small-format” midrange/full-range driver.
The X6 uses a copper shorting cup. The shorting cup consists of an optimally sized and plated copper (Cu) cup to create a total inductance profile that is not just low but flat over stroke, frequency, and power. Inductance is the number one limiter of high-frequency extension and modulation of inductance with stroke, frequency, and power, and is the primary source of intermodulation distortion (IMD).
The tinsel leads for the X6 are terminated on one side of the voice coil. The tinsel leads are stitched into the spider and bonded directly to the former and brought out to the terminals, which completely eliminates tinsel lead slap and does not compromise the structural integrity of the cone.
The Legatia X6 comes equipped with heavy-duty nickel-plated spring-loaded push terminals for both positive and negative. The terminals optimize contact and give the end user flexibility in tinned wire or binding post terminations.
The Legatia X6 is the ideal multi-purpose super high-end speaker driver. Mechanical and electrical parameters are amenable to a variety of different installations and speaker locations. This driver is intended to be used in an infinite baffle configuration; a simple, solid baffle, solidly attached to the car’s chassis with available airspace at the rear of the baffle is all that is required for optimum operation. The size of the X6 allows it to be mounted in typical “6-inch” midbass locations within a vehicle, or in custom locations at the discretion of the end-user, as long as there is adequate airspace behind the driver to allow it to maintain proper damping and acoustic suspension.
At home in virtually any arrangement, the X6 is Hybrid Audio Technologies Legatia X high-end large-format midrange/midbass offering, boasting exceptional performance and a design philosophy that goes hand in hand with true high-fidelity playback.