Proline X
Audiomobile GTS 2112 Box: Loaded Sealed 12" Slim Enclosure | Limited Edition
SKU: PO 12-S GTS Limited
- Best For: Shallow-Depth Trunk and Behind-Seat Builds, One-Off Limited Unit
- Net Volume: 0.78 cu ft (0.89 cu ft Gross)
- Driver Match: Audiomobile GTS 2112 S2 (included, wired and loaded)
- Construction: Sealed Slim Profile | V-Groove/Dado | Double 1.5" Baffle | Recessed Sides | Grille Included
Audiomobile GTS 2112 Box: Loaded Sealed 12" Slim Enclosure | Limited Edition
More enclosures cut for Audiomobile subwoofers: Audiomobile Subwoofer Boxes
Performance Optimized Limited | Audiomobile GTS 2112
12" Sealed Slim Enclosure | Woofer Loaded, Wired and Grilled | One Built
One Cabinet, Built Once, Loaded and Wired
This is a single limited build. One cabinet was cut, finished, loaded with an Audiomobile GTS 2112 S2 and wired to its terminal cup. When it sells it is gone; there is no second unit and no restock. It ships complete with the subwoofer fitted, the Audiomobile GSE 1012 grille installed and the polyfill already packed, so the only work left is running speaker wire to the cup and setting the gain.
The GTS 2112 is a 5.4 inch mounting depth 12 with a 499 square centimeter cone, 14.2 mm of one way excursion and a 277 gram moving mass. The motor label prints 400 watts RMS at a single 2 ohm load. The cabinet is 8 inches deep overall, which is what that 5.4 inch motor allows once a 1.5 inch double baffle and a 0.75 inch rear panel are accounted for, and it leaves 1.1 inches of air behind the magnet.
Why 0.78 Cubic Feet
Audiomobile recommend 0.75 to 1.25 cubic feet sealed for this driver, and the 2013 launch release for the GTS line puts the 2112 in 0.75 cubic foot enclosures. This cabinet holds 0.78 cubic feet net after the driver and the internal brace, so it sits at the small end of the range the maker published, which is the end this motor was designed around.
The GTS 2112 carries a total Q of 0.56. A maximally flat Butterworth alignment at Qtc 0.707 would need 3.07 cubic feet, which is not a trunk enclosure and not what a 5.4 inch deep driver is for. At 0.78 cubic feet the system lands at Qtc 1.02, system resonance 45.7 Hz, half power at 35.5 Hz anechoic. That is a deliberately tight sealed box: quick, loud for its size, with a lift around resonance that cabin gain extends below the anechoic figure.
Net Volume
0.78 cubic feet after driver displacement and the internal brace. Gross cavity 0.89 cubic feet. Audiomobile do not publish a displacement for the GTS 2112; 0.10 cubic feet is our estimate and the net figure carries it.
System Alignment
Qtc 1.02 with system resonance at 45.7 Hz. Above maximally flat, which is the only honest result for a 0.56 Qts driver in a cabinet this size.
Anechoic F3
35.5 Hz at half power, before any cabin gain. In a sedan trunk the usable response runs lower than that figure suggests.
Amplifier
280 to 400 watts RMS at 2 ohms. The driver is a single 2 ohm coil, so the final load is 2 ohms with no wiring choice to make.
How This One Is Built
Double 1.5" Baffle
Two laminated 0.75 inch layers behind the shell face. The GTS 2112 bolts to the full 1.5 inches rather than to a single sheet.
Recessed Side Panels
Both side panels drop into dados set 0.5 inch in from the shell edge, so each side sits in a recessed field rather than flush. The terminal cup lands in that recess.
Hexagon Routed Face
A hexagon is routed into the MDF baffle and the trunkliner is wrapped down into the groove, so the pattern reads as relief in the carpet rather than as a printed or applied graphic.
V-Groove and Dado Shell
The shell is a single strip, V-grooved and folded to four faces so the carpet runs unbroken around the corners. Internally braced and packed with polyfill.
Finished in Dark Gray Trunkliner with the terminal cup side mounted in the recessed panel. Overall 26.50 inches wide by 14.25 inches high by 8.00 inches deep. Ships at 48 pounds with the driver and grille fitted.
Wiring the GTS 2112
The GTS 2112 S2 is a single 2 ohm voice coil, already wired to the side mounted cup. There is no series or parallel decision and no second coil to bridge: whatever you connect sees 2 ohms. Confirm your amplifier is rated into 2 ohms before you connect it, and set gain against the 400 watt RMS figure printed on the motor rather than against a peak number.
Built in Tennessee, Backed by Audio Intensity
We cut, assemble, finish and load every Proline X enclosure in Tullahoma, Tennessee. We built this one as a single unit to see how the slim profile and the routed face came out, photographed it, and listed it rather than leaving it on the shelf. It carries the Performance Optimized one year warranty. Call or text us if you want a measurement taken off the actual cabinet before you buy; it is sitting here and we can put a tape on it.
One Unit, Loaded and Ready
Audiomobile GTS 2112 S2 fitted, wired, grilled and polyfilled in a slim 8 inch deep sealed cabinet. One built, one available.
| Specification | Value |
|---|---|
| Series | Proline X Performance Optimized, Limited Build |
| Driver Included | Audiomobile GTS 2112 S2 (single 2 ohm) |
| Grille Included | Audiomobile GSE 1012 |
| External Dimensions | 26.50" W x 14.25" H x 8.00" D |
| Net Volume | 0.78 cu ft |
| Gross Volume | 0.89 cu ft |
| System Q (Qtc) | 1.02 |
| System Resonance (Fc) | 45.7 Hz |
| Anechoic F3 | 35.5 Hz |
| Amplifier Power | 280 to 400 W RMS at 2 ohms |
| Final Impedance | 2 ohms |
| Baffle | 1.5" double layer |
| Panel Thickness | 0.75" |
| Side Panels | Recessed 0.50" into the shell |
| Face Detail | Hexagon routed into the baffle, trunkliner wrapped into the groove |
| Terminal Cup | 1, side mounted |
| Damping | Polyfill, installed |
| Covering | Dark Gray Trunkliner |
| Material | Langboard Elite MDF |
| Shipping Weight | 48 lb |
| Warranty | 1 Year |
| Built | Tullahoma, Tennessee |
01Is it a sealed driver?
Efficiency bandwidth product places the motor before anything else is decided.
02What the box does to it
0.78 cu ft against a 51.6 L Vas.
03The watts that reach Xmax (in this enclosure)
Travel scales with the square root of power, so there is one wattage that puts the cone exactly on 14.2 mm — and a bigger one once a subsonic filter stops it wasting travel below the passband.
| Param | Value | Unit | Note |
|---|---|---|---|
| Fs | 25.00 | Hz | free-air resonance |
| Qts | 0.560 | single 2 ohm | |
| Vas | 51.60 | L | equivalent compliance |
| Sd | 499.0 | cm² | effective piston area |
| Xmax | 14.2 | mm | one-way, as Audiomobile publish it |
| Pe | 400 | W | continuous RMS |
| SPL | 82.8 | dB | 1 W / 1 m, derived from T/S |
Driver parameters as published by Audiomobile published specifications. Curves computed against this enclosure’s actual net airspace.
Built From a Spec Sheet, Not a Sales Sheet
Every Proline X Performance Series enclosure is CNC-cut from Langboard Elite MDF, 3/4" (18mm) panels produced to published mill specifications. Most enclosure manufacturers source generic MDF without published data. We can tell you the internal bond rating, the modulus of elasticity, the modulus of rupture, and the face and edge screw holding strength for every panel in this enclosure, because we chose the material based on those numbers, not on price or availability.
Langboard Elite is produced in the United States. The specifications below are pulled directly from Langboard's published mill data and are verifiable. This is the same panel stock used in our full Proline X lineup.
Langboard Elite MDF: Published Mill Data
| Property | Value | Why It Matters |
|---|---|---|
| Panel Stock | Langboard Elite MDF | Named, verifiable panel source, not generic "high-density MDF" |
| Thickness | 3/4" (18mm) | Industry standard for subwoofer enclosures; panels below this flex under pressure |
| Density | 48.5 lbs/ft³ | Higher density = less porosity, better screw retention, reduced resonance |
| Internal Bond | 200 psi | Measures resistance to delamination under sustained internal pressure. The most enclosure-relevant spec on this sheet |
| Modulus of Rupture (MOR) | 4,200 psi | Bending strength before the panel breaks, relevant for larger unsupported baffle spans |
| Modulus of Elasticity (MOE) | 410,000 psi | Stiffness under load; higher MOE means less panel flex under bass pressure, less resonance |
| Face Screw Holding | 325 lbs | How firmly the panel surface holds a screw; critical for baffle joint integrity over time |
| Edge Screw Holding | 250 lbs | Panel edge retention, relevant for every joint that isn't face-to-face |
200 psi: The Number That Actually Matters for Enclosures
The internal bond rating measures how well the MDF panel resists delamination under sustained pressure applied perpendicular to the face. In a subwoofer enclosure, every bass transient generates a pressure pulse that pushes outward on every panel simultaneously. A panel that begins to delaminate internally loses stiffness gradually. The symptoms are slow: a box that starts to sound softer, less defined, less punchy over months of use. 200 psi internal bond is the spec that determines how long this enclosure holds its acoustic integrity under daily use at real power levels.
410,000 psi MOE: Less Flex, Less Resonance
The modulus of elasticity measures panel stiffness, its resistance to bending under load. A stiffer panel flexes less under the pressure generated by a high-excursion driver at volume. Panel flex is a source of acoustic coloration: the panel itself begins to radiate sound at its own resonant frequency, adding distortion to the output. 410,000 psi stiffness combined with V-groove and dado joinery means the panels stay rigid and the bracing controls resonance at the structure level, not the panel level. The bass you hear comes from the driver, not the box.
325 lb Face / 250 lb Edge: Joints That Stay Locked
Screw holding strength determines how firmly the panel grips a fastener at the face and at the edge. This matters most at the baffle joint, where the front panel meets the side panels and where the driver is mounted. A panel with low screw holding strength allows fasteners to loosen over time under vibration, leading to air gaps at the joint and loss of acoustic seal. 325 lb face screw holding strength means the baffle hardware stays put. Combined with dado joinery and adhesive, the front panel on a Proline X Performance Series enclosure is not going anywhere.
Named Panel Stock: Not "Premium MDF"
The phrase "premium MDF" or "high-density MDF" appears on marketing copy for enclosures across every price point, from $40 to $400. It is not a specification. It is a description with no defined standard. Langboard Elite is a named, sourced, mill-documented product with published data. We name it in our copy because naming it holds us accountable to the spec. You can look up Langboard Elite independently, verify the numbers on this page, and confirm you are getting what we say you are getting. That is the point.
Why Proline X?
Most enclosures are built to a price point. Proline X is built to a spec. Every box starts with published-data MDF, gets CNC-cut to exact internal volume, and is assembled by hand in our Tennessee facility. The difference shows up in the measurements, and in how the box holds up two years into daily use.
CNC-Cut to Spec
Panels are machine-cut on ShopSabre CNC routers and joined with V-groove and dado joinery. Consistent geometry, no hand-cut variance, no gaps at the joints.
Handcrafted in USA
Hand-assembled at our facility in Tullahoma, TN. Every enclosure is inspected before it ships.
Tuned to the Build
Internal volume and port geometry are calculated to spec and CNC-cut to exact dimensions. The box performs the same way every time.
Shop By Series








