Subwoofer Box for Truck: Which Fits Your Cab? (2026)
Cab type decides which subwoofer box fits your truck, so here's where a box can go in single, ext...
Read Article →Proline X
SKU: Pro 15-P XV415
More enclosures cut for Sundown Audio subwoofers: Sundown Audio Subwoofer Boxes
A ported fifteen-inch box built to Sundown's own numbers for the X-Series XV4 15
The Sundown Audio X-Series XV4 15 D2 carries a 15.51 inch frame and a 12.95 inch mounting depth, and this cabinet gives it 4.265 cubic feet net, vented at 32.0 Hz through an 82.5 square inch port beside the woofer on the front face. F3 lands at 26.4 Hz with 5.19 dB of passband ripple. The 33.5 by 18.0 by 25.0 inch enclosure carries a single 90 degree bend in the port, and the D1 version of this driver shares the same cabinet.
Threaded insert kit ships with this box. Sundown Audio does not publish the mounting hole locations for the X-Series XV4 15, so we cannot install the threaded inserts before it ships. The threaded insert kit comes in the box instead: inserts sized to the woofer, the correct drill bit, 2.5 inch allen-head screws, an allen key and woofer gasket tape. You set the inserts when you mount the woofer, and this box ships with one kit.
Sundown publishes a Qts of 0.440 for the X-Series XV4 15 D2, and the figure checks out against their own Qes of 0.490 and Qms of 4.080. Sundown does not recommend this driver sealed; their own ported figure is 4.25 cubic feet at 32 Hz through a 68 square inch port. This cabinet is built to that figure: 4.27 cubic feet net, tuned to 32.0 Hz. The one place it departs from Sundown's sheet is the port, 82.5 square inches against their 68, because at the coil's rated power, 2750 W, a 68 square inch slot would put the mouth over 17 metres per second. The port stays clean to 2751 W before mouth velocity becomes the limiting factor, the cone peaks at 13.8 of its 30.0 mm at rated power, and ripple across the passband holds at 5.19 dB.
Three layers of 3/4 inch Langboard Elite make a 2.25 inch front. The outer layer is routed to the flange, so the woofer sits flush with the face; the two layers behind it carry the mounting hardware and the load.
A glossy black acrylic insert with the Sundown Audio mark sits in the outer layer beside the woofer. It is standard on every Professional cabinet.
Threaded insert kit included, inserts NOT pre-installed: the manufacturer publishes no mounting hole locations, so the kit ships with the box for installation when the woofer goes in: 8 to 12 inserts sized to the woofer, the correct drill bit, 2.5 inch allen-head screws, allen key and gasket tape.
The 82.5 square inch slot beside the woofer is sized so the channel runs 21.6 metres per second and the mouth 17.0 metres per second at the driver's rated power, under the 17 metres per second where a slot starts to chuff. The channel runs 16.25 inches along its wall and turns once along the back wall for another 12.36 inches, which is why a 32.0 Hz tuning fits a 25.00 inch deep box.
Every driver is run through the Performance Optimized wedge and down-fire before this chassis; the Professional box is where a driver lands when that smaller envelope, 30 inches wide and 18 inches deep with a triangular side port, cannot give it what it needs at its rated power. The X-Series XV4 15 does not fit that envelope at all: no tuning, width or depth inside it carries a 12.95 inch deep 15 inch driver at 2750 W. This box is the chassis with the width, depth and port to carry it.
Every Professional cabinet is priced the same way, by its size: this one is 8.72 cubic feet outside. Delivery to the 48 states is inside the price; it ships as a 90 lb parcel and checkout adds nothing.
Sundown Audio publish a vented box for the X-Series XV4 15 at 4.25 cubic feet on a basis they do not state, tuned to 32.0 Hz. This cabinet holds 4.27 cubic feet net and tunes to 32.0 Hz. They call for a port area of 68 sq in.
33.50" W x 18.00" H x 25.00" D external. Two windowed braces run front to back either side of the woofer, clearing the cutout by two and a half inches. The box ships dry: polyfill detunes a ported alignment. This is our single-fifteen ported envelope built around the X-Series XV4 15's own frame and motor depth. It ships as a parcel.
Frame, cutout and mounting depth are Sundown's own published dimensions, and the Qts figure agrees with what its own Qes and Qms predict. Sundown prints the cone area as the nominal disc, so the 734 square centimetre figure behind this alignment is derived from their Vas and Cms instead. They list 30 mm of Xmax without stating how it was measured, and at rated power the cone uses 13.8 mm of it. The slot mouth runs 17.0 metres per second at 2750 W against the 17 metre per second point where a slot starts to chuff. The page's D1 column repeats the X-Series v.3 15's table, so this cabinet is solved on the D2 column, which is the XV4's own measurement; the D1 coil shares the same basket and fits the same cabinet. Sundown's page carries two power figures, 3000 W in the title and 2750 W in the spec table; this cabinet is designed against the lower one, which their notice on revised ratings makes the current figure. Sundown Audio does not publish the mounting hole locations for the X-Series XV4 15, so we cannot install the threaded inserts before it ships. The threaded insert kit comes in the box instead: inserts sized to the woofer, the correct drill bit, 2.5 inch allen-head screws, an allen key and woofer gasket tape. You set the inserts when you mount the woofer, and this box ships with one kit.
Set a 25 Hz subsonic filter, 24 dB per octave. Below tuning the vent stops loading the cone; with the filter in place the cone reaches 13.8 mm of its 30.0 mm at 2750 W.
| Series | Proline X Professional |
| Driver-Specific Fitment | Sundown Audio X-Series XV4 15 D2 (D2) |
| Enclosure Type | Ported | Front-Firing Standard Box |
| External Width | 33.50 Inches |
| External Height | 18.00 Inches |
| External Depth | 25.00 Inches |
| Internal Volume (Gross) | 6.51 Cubic Feet |
| Internal Volume (Net After Displacement) | 4.27 Cubic Feet |
| Port Type | Vertical Slot Beside The Woofer | Front Exit | One 90 Degree Bend Along The Back Wall |
| Port Geometry | 5.00 x 16.50 Inches, 82.5 Square Inches, 37.36 Inches Of Path |
| Port Area | 82.5 Square Inches |
| Port Tuning (Fb) | 32.0 Hz |
| Port Mouth | 1/2 In Roundover On All Four Edges, 105.0 Square Inches At The Face |
| Port Air Velocity | 21.6 m/s In The Channel, 17.0 m/s At The Mouth, At 2750 W (17.0 m/s Chuff Threshold) |
| Design Power Basis | 2750 W RMS (1.0 x The Driver Rating) For Port Velocity And Excursion |
| Predicted F3 | 26.4 Hz (Anechoic) |
| Passband Ripple | 5.19 dB (Anechoic) |
| Subsonic Filter | 25 Hz High-Pass, 24 dB/Octave - REQUIRED On A Vented Enclosure |
| Driver Fs | 29.51 Hz |
| Driver Qts | 0.440 |
| Driver Qes / Qms | 0.490 / 4.080 |
| Driver Vas | 40.410 Liters / 1.427 Cubic Feet |
| Driver Sd | 733.6 Square Centimeters |
| Driver Mms | 538.24 g |
| Driver BL | 27.44 |
| Driver Re | 3.7 Ohm |
| Driver Xmax | 30mm (One-Way) |
| Driver Displacement | 0.26 Cubic Feet (Published by Sundown Audio) |
| Driver Sensitivity | 85.1 dB |
| Driver Power Handling | 2750 Watts RMS |
| Driver Overall Diameter | 15.510 Inches (Sundown Audio Spec) |
| Mounting Depth Required | 12.950 Inches (Sundown Audio Spec) |
| Cutout Diameter | 13.930 Inches (Sundown Audio Spec) |
| Flush Mount Recess | 16.500 Inches In The Outer Layer |
| Material | Langboard Elite 3/4" MDF |
| Construction | ShopSabre CNC / Two Windowed Braces Front To Back Either Side Of The Woofer |
| Joinery | Dado Joinery (CNC-Cut), Flat Panels |
| Front Baffle Construction | Three 3/4" MDF layers, 2.25" total | Woofer Flush-Mounted In The Outer Layer |
| Baffle Layers | 3 |
| Acrylic | Glossy Black Sundown Audio Logo Insert, Outer Layer, Standard |
| Mounting Hardware | Threaded Insert Kit Included: 8-12 Inserts, Drill Bit, 2.5 In Allen-Head Screws, Allen Key, Gasket Tape |
| Voice Coil Configuration | D2 |
| Terminal Cup | Proline X ABS/Carbon Fiber Composite | Back Panel, Terminal-Cup Side | 12g OFC Pre-Wired |
| Damping | None - Ships Dry. Polyfill Detunes A Ported Enclosure |
| Recommended Power | 1924-2750 Watts RMS (Sundown Audio Rated: 2750W RMS) |
| Carpet Finish | Plush Black |
| Shipping Weight | 90 lb |
| Shipping | UPS Ground Parcel, Included In The 48 States |
| Bundle Options | Enclosure Only (Bring Your Own Sundown Audio X-Series XV4 15) |
| Warranty | 2-Year Limited (Enclosure) |
| Manufactured | Tullahoma, Tennessee, USA |
Efficiency bandwidth product places the motor before anything else is decided.
4.27 cu ft net against a 40.4 L Vas, vented at 32.0 Hz.
No sealed comparison is shown for this driver.
Travel scales with the square root of power, so there is one wattage that puts the cone exactly on Sundown's published 30.0 mm. The two traces are the same cabinet with the subsonic filter switched on and switched off.
| Driver | Sundown Audio X-Series XV4 15 |
| Coil Options | Dual 1 Ohm or Dual 2 Ohm |
| Motor | Heavy Duty, 9.25 in Diameter |
| Motor Diameter | 9.25 in |
| RMS Power | 2750 W |
| Peak Power | 5500 W |
| Sensitivity | 85.29 dB (D1), 85.1 dB (D2), Sensitivity, reference condition not stated by Sundown Audio |
| Mounting Depth | 12.95 in |
| Cutout Diameter | 13.93 in |
| Frame Outside Diameter | 15.51 in |
| Driver Displacement | 0.26 cu ft |
| Driver Warranty | 2 Year Limited, Authorized Dealer Purchase, Original Owner |
Every Proline X Professional Series enclosure is CNC-cut from Langboard Elite MDF, 3/4" (18mm) panels produced to published mill specifications. Most enclosure manufacturers source generic MDF without published data. We can tell you the internal bond rating, the modulus of elasticity, the modulus of rupture, and the face and edge screw holding strength for every panel in this enclosure, because we chose the material based on those numbers, not on price or availability.
Langboard Elite is produced in the United States. The specifications below are pulled directly from Langboard's published mill data and are verifiable. This is the same panel stock used in our full Proline X lineup.
| Property | Value | Why It Matters |
|---|---|---|
| Panel Stock | Langboard Elite MDF | Named, verifiable panel source, not generic "high-density MDF" |
| Thickness | 3/4" (18mm) | Industry standard for subwoofer enclosures; panels below this flex under pressure |
| Density | 48.5 lbs/ft³ | Higher density = less porosity, better screw retention, reduced resonance |
| Internal Bond | 200 psi | Measures resistance to delamination under sustained internal pressure. The most enclosure-relevant spec on this sheet |
| Modulus of Rupture (MOR) | 4,200 psi | Bending strength before the panel breaks, relevant for larger unsupported baffle spans |
| Modulus of Elasticity (MOE) | 410,000 psi | Stiffness under load; higher MOE means less panel flex under bass pressure, less resonance |
| Face Screw Holding | 325 lbs | How firmly the panel surface holds a screw; critical for baffle joint integrity over time |
| Edge Screw Holding | 250 lbs | Panel edge retention, relevant for every joint that isn't face-to-face |
The internal bond rating measures how well the MDF panel resists delamination under sustained pressure applied perpendicular to the face. In a subwoofer enclosure, every bass transient generates a pressure pulse that pushes outward on every panel simultaneously. A panel that begins to delaminate internally loses stiffness gradually. The symptoms are slow: a box that starts to sound softer, less defined, less punchy over months of use. 200 psi internal bond is the spec that determines how long this enclosure holds its acoustic integrity under daily use at real power levels.
The modulus of elasticity measures panel stiffness, its resistance to bending under load. A stiffer panel flexes less under the pressure generated by a high-excursion driver at volume. Panel flex is a source of acoustic coloration: the panel itself begins to radiate sound at its own resonant frequency, adding distortion to the output. 410,000 psi stiffness combined with V-groove and dado joinery means the panels stay rigid and the bracing controls resonance at the structure level, not the panel level. The bass you hear comes from the driver, not the box.
Screw holding strength determines how firmly the panel grips a fastener at the face and at the edge. This matters most at the baffle joint, where the front panel meets the side panels and where the driver is mounted. A panel with low screw holding strength allows fasteners to loosen over time under vibration, leading to air gaps at the joint and loss of acoustic seal. 325 lb face screw holding strength means the baffle hardware stays put. Combined with dado joinery and adhesive, the front panel on a Proline X Professional Series enclosure is not going anywhere.
The phrase "premium MDF" or "high-density MDF" appears on marketing copy for enclosures across every price point, from $40 to $400. It is not a specification. It is a description with no defined standard. Langboard Elite is a named, sourced, mill-documented product with published data. We name it in our copy because naming it holds us accountable to the spec. You can look up Langboard Elite independently, verify the numbers on this page, and confirm you are getting what we say you are getting. That is the point.
Most enclosures are built to a price point. Proline X is built to a spec. Every box starts with published-data MDF, gets CNC-cut to exact internal volume, and is assembled by hand in our Tennessee facility. The difference shows up in the measurements, and in how the box holds up two years into daily use.
Panels are machine-cut on ShopSabre CNC routers and joined with V-groove and dado joinery. Consistent geometry, no hand-cut variance, no gaps at the joints.
Hand-assembled at our facility in Tullahoma, TN. Every enclosure is inspected before it ships.
Internal volume and port geometry are calculated to spec and CNC-cut to exact dimensions. The box performs the same way every time.








