Kicker
Kicker 46TL7T122 Sealed 2-ohm enclosure with single square L7T Series 12" shallow-mount subwoofer | Display
Kicker 46TL7T122 Sealed 2-ohm enclosure with single square L7T Series 12" shallow-mount subwoofer | Display
Previous display unit
Kicker 46TL7T122 Sealed Loaded Enclosure with 12 Inch L7T
Truck wedge, sealed, 3/4 inch MDF. Square 12 inch L7T shallow-mount driver, dual 4 Ohm coils wired to a 2 Ohm final load. 600W RMS, 25Hz to 100Hz, 7.75 inch base depth.
- Display unit
- Loaded enclosure
- Shallow mount
- Sold as-is
Where this sits in what we do
We are not a Kicker dealer and we do not stock Kicker drivers. This is a single previously displayed unit off our own floor. We do cut enclosures to Kicker drivers on our routers, and if you want a box built to a driver you already own, that is a different conversation and we are happy to have it.
What You Are Buying
A loaded sealed enclosure: a square 12 inch L7T shallow-mount subwoofer already mounted in a carpeted MDF truck wedge, pre-wired to a 2 Ohm final load. One unit, previously on display.
Condition, stated plainly
This unit has been on display. Expect handling marks on the carpet and the driver. It is sold as-is. Ask us about condition before you buy and we will describe exactly what it looks like.
Reading the Specification
Dual 4 Ohm coils wired to 2 Ohm
Two 4 Ohm coils in parallel give a 2 Ohm final load. That is fixed by the terminal wiring on this enclosure; you cannot get 1 Ohm or 4 Ohm out of it without opening the box and rewiring. Size your amplifier for 2 Ohms.
600W RMS, 1200W peak
600W is the number to plan against. A 400 to 500W monoblock at 2 Ohms is a comfortable, safe match and will not leave anything meaningful on the table. Going far above 600W means relying entirely on your gain discipline, and a clipped signal from an underdriven amplifier destroys more voice coils than clean power from a large one ever has.
86.54dB sensitivity, 25Hz to 100Hz
Sealed, so the rolloff below the passband is gentle rather than a cliff, and the transient behavior is tighter than a ported box of the same size. 25Hz on a sealed 12 in a small box is a claim about where output is still measurable, not where it is flat.
Square cone
The L7T's square cone is the reason Kicker built it that way: a square fits more radiating area into the same mounting footprint than a circle does. More area means more air moved per millimeter of excursion. The trade is a surround that has to flex differently along the sides than at the corners, which is why square drivers use a specialized surround.
7.75 inch base depth, 4.375 inch top depth
The wedge is what makes this fit behind a seat. The angled face means the top of the box is under four and a half inches deep while the base is under eight, so it tucks against a seat back where a rectangular box of the same volume would not.
The Enclosure
We build enclosures here, so a few observations on this one from someone who cuts MDF for a living.
- 3/4 inch MDF with internal bracing. Correct thickness for a box this size, and the bracing is what stops the large flat panels acting as a second, out-of-phase driver.
- Sealed. The right alignment for a shallow-mount driver in a small volume. A ported box that size would need a port so small it would choke.
- Carpet with rounded corners. Rounded corners are not cosmetic. Carpet frays at a sharp 90 degree edge and a rounded one holds it.
- Spring post terminals. They accept up to 10 gauge, bare wire, pins or banana plugs. Serviceable, and easier to work with in a cramped cab than a screw terminal.
Fitment
- 21.5 x 13.75 x 7.75 inches at the base, 4.375 inches deep at the top.
- 36 lbs loaded. Plan on two people for the install.
- Designed for behind-seat mounting in crew cab and extended cab trucks. Regular cabs generally do not have the room.
- The wedge angle faces the seat backs.
Measure your space before you buy. On a used display unit with one in stock, that is not a formality.
Who This Suits
Buy this if
- You have a crew cab or extended cab truck and want bass without losing the bed or the back seat.
- You have or will buy a 400 to 600W monoblock stable at 2 Ohms.
- You want sealed, controlled bass rather than maximum output.
- You accept a used display unit sold as-is.
Look elsewhere if
- Your amplifier is 1 Ohm only. This load is fixed at 2 Ohm.
- You want a ported box or maximum SPL.
- You have a regular cab.
- You want new stock with full warranty, or a box cut to a driver you already own. Talk to us about the second one.
Installation
- Measure width, height and both depths against your space before committing.
- Use 12 to 14 gauge speaker wire; the terminals take up to 10 gauge.
- Secure the box. 36 lbs loose behind a seat is a hazard, not just a rattle.
- Set the amplifier low-pass around 80Hz and the gain by ear at your normal maximum volume.
- No subsonic filter is required on a sealed box, though a shallow one below 20Hz does no harm.
Condition and sale terms
Previously displayed unit, sold as-is. It has been handled and may show cosmetic marks on the carpet and driver. Specifications are as published by Kicker. Audio Intensity is not a Kicker dealer and does not stock Kicker drivers; this is a single unit from our own display floor. Once it is gone this listing will be removed.
Ask us for condition photos and measurements before you buy: contact us.
| Type | Loaded sealed enclosure, truck wedge |
|---|---|
| Driver | 12 inch square L7T shallow mount |
| Cone | Polypropylene, square |
| Voice coil configuration | Dual 4 Ohm, pre-wired parallel |
| Final impedance | 2 Ohm |
| Condition | Previously displayed unit, sold as-is |
| RMS power | 600W |
|---|---|
| Peak power | 1200W |
| Recommended amplifier | 400 to 500W RMS monoblock, stable at 2 Ohm |
| Sensitivity | 86.54 dB |
|---|---|
| Frequency response | 25Hz to 100Hz |
| Alignment | Sealed |
|---|---|
| Material | 3/4 inch MDF with internal bracing |
| Finish | Black carpet, rounded corners |
| Terminals | Spring posts, accepts up to 10 AWG |
| Width | 21.5 inch |
|---|---|
| Height | 13.75 inch |
| Base depth | 7.75 inch |
| Top depth | 4.375 inch, wedge |
| Weight loaded | 36 lbs |
| Speaker wire | 12 to 14 AWG |
The 2 Ohm final load is fixed by the enclosure terminal wiring. Getting 1 Ohm or 4 Ohm out of this box means opening it and rewiring the driver.





