Arc Audio
Arc Audio Moto CX69 6x9 Motorcycle Speaker Set
SKU: Moto CX69
Arc Audio Moto CX69 6x9 Motorcycle Speaker Set
What You Are Buying
A pair of Arc Audio Moto CX69 speakers: 6x9 two-way, built for the open air on a motorcycle, a trike or a side-by-side. New stock, sold as a closeout.
This is a model we do not normally carry. When these two sets are gone, the listing goes with them.
Read This Before You Buy
Final sale. No returns, no exchanges and no warranty coverage on this purchase. The speakers are new, not used or refurbished.
It Is Not Really a Coaxial
Arc describes the CX69 as technically a component set, because the tweeter is mounted on a bridge that spans the cone rather than on a pole piece poking through the middle of it. You still install it like a coaxial, in one 6x9 opening with one pair of wires.
The reason that matters is cone area. On the Moto692 this replaced, the tweeter sat in the center of the woofer and needed a second weather-resistant surround sealing around the pole piece. Moving the tweeter onto a bridge deletes that second surround and hands the space back to the cone. More cone area is more efficiency and more low-frequency output from the same hole, and Arc says losing that second surround improves sound quality by itself.
Built for Sun, Rain and Vibration
- Cone: injection-molded polypropylene doped with carbon, which raises thermal stability and improves damping.
- Surround: hi-clearance, low-shore rubber. Entirely UV-resistant materials throughout.
- Dust cap: form-molded, dual-step, sealed one-piece, covering the tri-layered bonded joint where cone, spider and former meet.
- Spider: hybrid Nomex with a constant-wave progressive roll, so the assembly resists bottoming out at high power.
- Bonding: the spider, coil former and cone are stagger-step bonded with adhesive rated above 230 degrees C, which is over 440 degrees F.
The Motor and Basket
The basket is a high-density pressure-cast four-spoke design with eight large high-velocity cooling vents under the spider mounting plateau, so heat from the voice coil has somewhere to go.
The motor uses a Y35A-grade ferrite magnet with a CNC-cut hot-rolled steel top plate. Ferrite rather than neodymium is a deliberate choice here: the magnet's mass works as a thermal heat sink that pulls heat away from the voice coil. On a speaker mounted in a fairing in direct sun, shedding heat is worth more than saving weight.
The voice coil is 1.45 inches, wound in pure OFC copper on a layered Kapton and glass fiber former. A large coil diameter means more surface area to dump heat through, which is what lets Arc rate the speaker at 125 watts musical and 300 watts peak and describe it as handling that rating easily.
The Tweeter
A 25 mm polyetherimide and mylar dome, damped with Norseal PVC mesh, in a sealed and suspended assembly on a neodymium slug motor. That composite dome construction is borrowed from pro audio compression drivers, where a diaphragm has to be stiff, well damped, and indifferent to heat and weather at the same time. On a bike, all three apply.
Specifications
| Type | 6x9 two-way, tweeter on a bridge |
|---|---|
| Sold as | Pair |
| Power, musical (RMS) | 125 watts |
| Power, peak | 300 watts |
| Voice coil | 1.45 inch, OFC on Kapton and glass fiber |
| Magnet | Y35A ferrite, CNC-cut hot-rolled steel top plate |
| Cone | Carbon-doped injection-molded polypropylene |
| Basket | Pressure-cast four-spoke, eight cooling vents |
| Tweeter | 25 mm PEI and mylar dome, Norseal damped, neodymium |
| Condition | New, closeout, final sale |
On the Numbers Arc Does Not Publish
Arc Audio's product page for the CX69 has a Specifications tab, and it is empty. There is no impedance, sensitivity, frequency response, mounting depth or cutout figure published by the manufacturer for this model.
The figures that circulate on dealer listings are roughly 4 ohms, 95 dB sensitivity, 50 Hz to 20 kHz, 3.25 inches of mounting depth, a 5.82 by 8.62 inch cutout and a 4.3 inch motor diameter. Those are consistent with each other and with the design, but they are not Arc's published numbers and we are not going to present them as though they were.
If clearance is tight, ask us first. We have stock in hand and can measure a set before it ships.
Who This Suits
Buy these if you are replacing 6x9 speakers in a fairing, a lid or a saddlebag; you have an amplifier in the 75 to 125 watt per channel range; you want real weather engineering rather than a car speaker with a rubber surround; and you accept a final sale.
Look elsewhere if you need published sensitivity or response curves to model a system; your mounting depth is tight and you cannot wait for us to measure; or you need the option to return.
Installation
- Test-fit before you cut. The bridge-mounted tweeter sits above the cone, so check clearance in front of the speaker as well as behind it, especially under a lid or grille.
- Seal the mounting surface. Weather-resistant materials protect the speaker, not the cavity behind it.
- Run them off an amplifier. These are efficient, but an open bike at speed has no cabin to help you, and headroom is what keeps the sound clean at road speed.
- Set gains by ear at a speed you actually ride at. Wind noise masks distortion, which is how motorcycle speakers usually die.
Condition and Sale Terms
New closeout stock of a model we do not normally carry. Sold as a final sale with no returns, no exchanges and no warranty coverage. Packaging may show shelf wear. Construction details above are taken from Arc Audio's own product description; the dimensional figures are dealer-published and flagged as such. Once these are gone this listing will be removed.
Questions on fitment, depth or amplifier matching before you buy: contact us.