Blow Through Sub Box Design: Cutting, Sealing and Truck F...
A blow through sub box fires into the cab through an opening cut in the rear cab wall, so the enc...
Read Article →Proline X
SKU: PX-BRONCO-Q10S-SW10-1
More enclosures cut for Arc Audio subwoofers: Arc Audio Subwoofer Boxes
A custom downfire enclosure for four Arc Audio SW10 in a 42 by 17 inch footprint, two sealed chambers, 2.39 cubic feet net
Special order, built for you. This cabinet is cut and built after you order it and ships within 15 working days of purchase.
This box puts four 10 inch Arc Audio SW10 drivers into a 42 inch wide, 17 inch deep footprint at 9.125 inches tall, 11.625 inches with the feet. It holds 2.45 cubic feet gross and 2.39 net, split into two sealed chambers so every driver works against 0.60 cubic feet. That is a Qtc of 0.85 with an anechoic F3 of 45.9 Hz, and in a Bronco cabin the rolloff below that is largely filled in by cabin gain.
The SW10 is Arc Audio's 2.4 inch deep 10, a 0.63 Qts driver with 14.7 mm of travel, a 9.1 inch cutout and a 10.3 inch frame. Arc publishes its sealed range as 0.4 to 0.9 cubic feet gross with 0.6 optimum; at 0.60 cubic feet net per driver this box sits just above that optimum, at Qtc 0.85. Its motor mounts on the front of the driver, so in a downfire box the motor hangs in the floor gap, in open air, instead of in the sealed chamber.
Two drivers along the front and two along the back, staggered so four 10.3 inch frames fit a 42 inch by 17 inch baffle with 0.72 inch edges. The drivers surface-mount on a 1.50 inch double baffle, the bottom panel of the box.
A 3/4 inch center divider splits the box into two sealed chambers of 1.20 cubic feet net. Drivers 1 and 2 share the left chamber, 3 and 4 the right, and each chamber has its own terminal cup on the back wall so the pairs can be wired and fed independently.
Six 1.5 by 1.5 inch feet hold the baffle 2.50 inches off the floor. The cones fire into that gap and the bass comes out around all four sides of the box. The SW10's motor is mounted on the front of the driver, so in this box it sits in that floor gap, in open air below the baffle.
Each chamber has two 3/4 inch MDF window braces running front to back, one off the front wall and one off the back wall, set in the gap between the staggered drivers. Each brace is glued to the baffle, the top panel and its wall, with a 1.50 inch frame around an open window so air moves freely, and each stops 1/4 inch short of the woofer cutout. With the center divider, that ties the baffle, top and long front and back panels together in the middle of each chamber.
Delivery to the 48 states is inside the price and checkout adds nothing. Special order: built after purchase and shipped within 15 working days. The loaded options include four Arc Audio SW10 drivers, dual 2 ohm or dual 4 ohm, installed and wired.
The four SW10 drivers are rated 350 W RMS each, 1400 W total, and that thermal rating is the ceiling. Mechanically they reach their 14.7 mm of travel on about 2740 W without a subsonic filter and about 2980 W with a 25 Hz filter, roughly twice the rating, so travel is not the limit at rated power. A light layer of fill is fine in a sealed box.
| Series | Proline X Custom | Vehicle: Ford Bronco |
| Availability | Special Order | Ships Within 15 Working Days Of Purchase |
| Driver-Specific Fitment | Arc Audio SW10D2 or SW10D4 (x4) | 350 W RMS Each | 14.7 mm Xmax | 2.4 In Mounting Depth |
| Enclosure Type | Sealed | Downfire | Quad 10" |
| External Width | 42.00 Inches |
| External Depth | 17.00 Inches |
| External Height | 9.125 Inches (11.625 Inches With Feet) |
| Internal Volume (Gross) | 2.45 Cubic Feet |
| Internal Volume (Net After Displacement) | 2.39 Cubic Feet (After Drivers, Divider And Bracing) |
| Chambers | 2 Sealed Chambers, 1.20 Cubic Feet Net Each, 2 Drivers Per Chamber |
| Volume Per Driver | 0.60 Cubic Feet |
| System Qtc | 0.85 |
| Predicted F3 | 45.9 Hz (Parallel) / 46.4 Hz (Series) (Anechoic) |
| Baffle | 1.50 In Double 3/4 MDF | Bottom Panel | Surface Mount, Staggered |
| Cutout Diameter | 9.1 In (Arc Audio Spec) |
| Driver Spacing | Front Row At 5.87 In From Front Edge, Back Row At 11.12 In | Divider At Center |
| Internal Bracing | 3/4 In Center Divider (Dado Set) + 2 Front-To-Back 3/4 In MDF Window Braces Per Chamber, Baffle To Top |
| Motor Clearance | Front-Mounted N42UH Motor Sits In The 2.50 In Floor Gap | 5.97 In Basket To Top Panel (2.40 In Mounting Depth) |
| Feet | 6x 1.5 x 1.5 x 2.5 In | 2.50 In Floor Gap |
| Terminal Cups | 2 (One Per Chamber), Back Panel, Pre-Wired |
| Material | Langboard Elite 3/4" MDF |
| Construction | ShopSabre CNC | Dado Joinery |
| Carpet Finish | Plush Black |
| Damping | Light Fill Recommended For Sealed (Optional) |
| Shipping Weight | 52 lb Enclosure Only | 92 lb Loaded (Est.) |
| Shipping | Included In The 48 States |
| Warranty | 2-Year Limited (Enclosure) |
| Manufactured | Tullahoma, Tennessee, USA |
Efficiency bandwidth product places the motor before anything else is decided.
2.45 cu ft gross, 2.39 cu ft net in two sealed chambers: 0.60 cu ft per driver against a 13.3 L Vas.
Why the layout is what it is.
Travel scales with the square root of power, so there is one wattage that puts all four cones on the published 14.7 mm. Power figures are for all four drivers, split evenly.
| Driver | Arc Audio SW10D2 / SW10D4 |
| Coil | Dual 2 Ohm / Dual 4 Ohm |
| Voice Coil Diameter | 2.5 in |
| Coil Former | Aluminum, Stage-Baked Tempered Coil |
| Motor | Front-Mounted N42UH Neodymium, Outside The Enclosure |
| Motor Cap | CNC-Machined Vented Iron |
| Cone | Reinforced Cellulose Fiber, Raised-Cup Profile, Hydrophobic Coating |
| Surround | Low-Shore Butyl Rubber |
| Spider | Nomex / Cotton Blend |
| Terminals | High-Tension Spring-Loaded |
| Power Handling | 350 W RMS / 700 W Peak |
| Fs | 39 Hz |
| Qts | 0.634 |
| Qes / Qms | 0.736 / 4.589 |
| Vas | 13.33 L |
| Sd | 338.16 cm² |
| Re | 0.97 Ohm (D2, Parallel) |
| Bl | 8.085 T·m |
| Mms | 201.8 g |
| Sensitivity | 83.35 dB, 1W/1m |
| Xmax, One-Way | 14.7 mm |
| Arc Sealed Range | 0.4 Min / 0.6 Recommended / 0.9 Max cu ft |
| Mounting Depth | 2.4 in (2.25 in Front Load) |
| Cutout Diameter | 9.1 in |
| Outer Diameter | 10.3 in |
| Driver Warranty | 1 Year, Authorized Arc Audio Dealer |
Every Proline X Professional Series enclosure is CNC-cut from Langboard Elite MDF, 3/4" (18mm) panels produced to published mill specifications. Most enclosure manufacturers source generic MDF without published data. We can tell you the internal bond rating, the modulus of elasticity, the modulus of rupture, and the face and edge screw holding strength for every panel in this enclosure, because we chose the material based on those numbers, not on price or availability.
Langboard Elite is produced in the United States. The specifications below are pulled directly from Langboard's published mill data and are verifiable. This is the same panel stock used in our full Proline X lineup.
| Property | Value | Why It Matters |
|---|---|---|
| Panel Stock | Langboard Elite MDF | Named, verifiable panel source, not generic "high-density MDF" |
| Thickness | 3/4" (18mm) | Industry standard for subwoofer enclosures; panels below this flex under pressure |
| Density | 48.5 lbs/ft³ | Higher density = less porosity, better screw retention, reduced resonance |
| Internal Bond | 200 psi | Measures resistance to delamination under sustained internal pressure. The most enclosure-relevant spec on this sheet |
| Modulus of Rupture (MOR) | 4,200 psi | Bending strength before the panel breaks, relevant for larger unsupported baffle spans |
| Modulus of Elasticity (MOE) | 410,000 psi | Stiffness under load; higher MOE means less panel flex under bass pressure, less resonance |
| Face Screw Holding | 325 lbs | How firmly the panel surface holds a screw; critical for baffle joint integrity over time |
| Edge Screw Holding | 250 lbs | Panel edge retention, relevant for every joint that isn't face-to-face |
The internal bond rating measures how well the MDF panel resists delamination under sustained pressure applied perpendicular to the face. In a subwoofer enclosure, every bass transient generates a pressure pulse that pushes outward on every panel simultaneously. A panel that begins to delaminate internally loses stiffness gradually. The symptoms are slow: a box that starts to sound softer, less defined, less punchy over months of use. 200 psi internal bond is the spec that determines how long this enclosure holds its acoustic integrity under daily use at real power levels.
The modulus of elasticity measures panel stiffness, its resistance to bending under load. A stiffer panel flexes less under the pressure generated by a high-excursion driver at volume. Panel flex is a source of acoustic coloration: the panel itself begins to radiate sound at its own resonant frequency, adding distortion to the output. 410,000 psi stiffness combined with V-groove and dado joinery means the panels stay rigid and the bracing controls resonance at the structure level, not the panel level. The bass you hear comes from the driver, not the box.
Screw holding strength determines how firmly the panel grips a fastener at the face and at the edge. This matters most at the baffle joint, where the front panel meets the side panels and where the driver is mounted. A panel with low screw holding strength allows fasteners to loosen over time under vibration, leading to air gaps at the joint and loss of acoustic seal. 325 lb face screw holding strength means the baffle hardware stays put. Combined with dado joinery and adhesive, the front panel on a Proline X Professional Series enclosure is not going anywhere.
The phrase "premium MDF" or "high-density MDF" appears on marketing copy for enclosures across every price point, from $40 to $400. It is not a specification. It is a description with no defined standard. Langboard Elite is a named, sourced, mill-documented product with published data. We name it in our copy because naming it holds us accountable to the spec. You can look up Langboard Elite independently, verify the numbers on this page, and confirm you are getting what we say you are getting. That is the point.
Most enclosures are built to a price point. Proline X is built to a spec. Every box starts with published-data MDF, gets CNC-cut to exact internal volume, and is assembled by hand in our Tennessee facility. The difference shows up in the measurements, and in how the box holds up two years into daily use.
Panels are machine-cut on ShopSabre CNC routers and joined with V-groove and dado joinery. Consistent geometry, no hand-cut variance, no gaps at the joints.
Hand-assembled at our facility in Tullahoma, TN. Every enclosure is inspected before it ships.
Internal volume and port geometry are calculated to spec and CNC-cut to exact dimensions. The box performs the same way every time.








