Proline X
Proline X P10-S W | Single 10" Sealed Wedge Subwoofer Enclosure | Loaded with Arc Audio X2V2 10
SKU: P10-S W ARC X2V2 D4 G
- Best For: Behind-seat and bulkhead installs where a square box wastes floor
- Configuration: Single 10" Sealed Wedge — Performance Series, loaded
- Volume: 0.70 ft³ Net
- Tuning: N/A — Sealed
- Sonic Character: Warm, punchy, midbass forward
Financing available — choose Shop Pay Installments at checkout.
What's Included
Proline X P10-S W | Single 10" Sealed Wedge Subwoofer Enclosure | Loaded with Arc Audio X2V2 10
Built for the Arc Audio X2V2 10.
Sealed Wedge, Loaded and Wired.
The X2V2 10 carries 14.8mm of one-way linear Xmax and a 200 watt RMS rating that reflects sustained thermal capacity rather than a peak figure. The Proline X P10-S W delivers 0.70 cubic feet of sealed airspace in the most compact wedge we build, leaning into a seat back rather than standing square in your cargo area. The driver arrives mounted, wired and sealed against the baffle.
0.70 cu ft — Toward the Tighter End of Arc's Range
Arc Audio publishes a sealed range of 0.65 to 1.0 cubic feet for the X2V2 10. This enclosure is 0.70 cubic feet net, sitting near the lower end of that range rather than in the middle.
A smaller sealed box raises system Qtc. That trades a little anechoic extension for more midbass punch and tighter transient control. In a vehicle, where cabin gain already adds 6 to 12 dB below 80 Hz, most of what the smaller cabinet gives up on paper is restored in the listening position while the added control is audible straight away.
If you want the more relaxed alignment at the top of Arc's range, you want a larger cabinet than this wedge provides. Worth knowing before you order rather than after.
The Most Compact Wedge We Build
At 14.5 inches wide and 13 inches tall, tapering from 8.5 inches deep at the top to 13 at the bottom, this is a genuinely small footprint for a 10 inch sealed system. It fits compact hatches and small SUV cargo areas where the 12 inch wedge would be tight.
Mounted shallow edge up it leans into a rear seat back or bulkhead and occupies the space that was already awkward, leaving the flat cargo floor usable. The roughly 20 degree taper also keeps the baffle out of parallel with the rear glass, which reduces the standing wave behaviour you get when a large flat radiating surface faces a large flat reflecting one.
The X2V2 10 — Rated Conservatively, Built for Daily Use
Arc Audio's power testing philosophy is to double test power after each successful round until something actually fails, which is why the 200 watt RMS figure reflects sustained thermal capacity rather than a peak dressed up as continuous.
The motor uses double stacked magnets and a 2 inch copper coated aluminium voice coil on a Kapton former, anodised black for radiative heat dissipation. The four spoke stamped steel basket carries eight integrated motor cooling vents plus a T-yoke centre vent. The cone is reinforced pulp paper with a moisture resistant coating, the surround is large diameter rubber rather than foam, and the high roll Conex spider has the tinsel leads woven directly into it, which removes the bare lead designs that cause cone slap and shorts over time.
0.70 cu ft Net, Calculated Not Estimated
Net internal volume is 0.70 cubic feet after bracing and driver displacement, calculated from the cut geometry rather than derived from external dimensions minus an assumed wall thickness.
14.8mm Xmax, 346 cm² Cone
The X2V2 10 carries 14.8mm of one-way linear Xmax with 85 dB sensitivity and a 129 gram moving mass. Enough travel to produce real output at this volume without running out of stroke at listening levels.
0.75" Single Baffle, 9.25" Cutout
Cut from Langboard Elite 3/4" MDF with a 9.25 inch machined opening. Max mounting depth is 8 inches, comfortable clearance for a standard depth 10 inch driver.
Pre-Wired 12g OFC to the Terminal Cup
The recessed Proline X ABS and carbon fiber terminal cup with stainless hardware and copper ring terminals is installed and wired to the driver. Connect your amplifier run and the wiring is finished.
14.5" Wide — Fits Where the 12 Will Not
The smallest wedge in the Performance line. Compact hatches and small SUV cargo areas that cannot take the 16 inch wide 12 inch version will usually take this.
Polyfill Installed at the Bench
Fitted and matched to this volume before the cabinet is sealed. Polyfill slows the speed of sound inside the box, making it behave acoustically larger than its physical net volume. Consistent packing density on every unit.
Shallow Edge Up, Deep Edge Down
The wedge only pays off mounted the right way round. Shallow edge up, leaning back into the seat. Fitted inverted it stands proud and puts the baffle back parallel with the glass.
Dark Gray Trunkliner or Plush Black
Both wrap the full cabinet including the tapered face. Choose above. Plush black is the deeper pile of the two and hides handling marks better in a cargo area that gets used.
Ready to Mount. Ready to Wire.
The system ships fully assembled. The driver is mounted, gasketed and sealed against the baffle, and wired to the Proline X terminal cup with 12 gauge OFC. Polyfill is installed. Connect your amplifier run and the install is complete.
Impedance Options — D2 and D4
The X2V2 10 is available as a Dual 2 ohm (D2) and a Dual 4 ohm (D4). Wire the D2 parallel for 1 ohm or series for 4 ohms. Wire the D4 parallel for 2 ohms or series for 8 ohms. Most single subwoofer builds run the D4 parallel at 2 ohms into a 2 ohm stable monoblock delivering 150 to 200 watts RMS. Confirm your amplifier's minimum stable impedance before selecting the voice coil.
Where It Fits
At 14.5 inches wide and 13 tall, tapering from 8.5 to 13 inches deep, this cabinet is designed to live against a vertical surface rather than in the middle of a floor:
- Behind a rear seat back in a compact SUV or crossover
- Against a bulkhead in a hatchback
- Trunk front wall in a compact sedan, facing rearward
- Extended cab trucks, behind the seat
- Wagon cargo area against the seat back
- Any install where a square box eats usable floor
Proline X Performance Series enclosures carry a one-year limited warranty against defects in materials and workmanship. Built and inspected in our Tullahoma, Tennessee facility before shipment. The Arc Audio X2V2 10 carries its own one-year manufacturer warranty, handled through Arc Audio.
Made in Tennessee
Every Proline X enclosure is CNC cut and hand assembled in Tullahoma, Tennessee on ShopSabre routers. Internal volume, cutout geometry, wedge angle, bracing placement and terminal positioning are held to spec on every unit. Langboard Elite MDF throughout, named, mill documented, with published density and internal bond specifications.
| Enclosure | Proline X P10-S W, Performance Series sealed wedge |
| Driver | Arc Audio X2V2 10, pre-installed |
| Voice Coil | Dual, available D2 or D4 |
| Material | Langboard Elite MDF, 3/4" (18mm) |
| Enclosure Type | Sealed |
| Net Internal Volume | 0.70 ft³ Net |
| Tuning Frequency | N/A — Sealed |
| External Width | 14.5" |
| External Height | 13" |
| External Depth (Top) | 8.5" — shallow end |
| External Depth (Bottom) | 13" — deep end |
| Wedge Angle | ~20° taper |
| Subwoofer Cutout | 9.25" |
| Max Mounting Depth | 8" |
| Front Panel Thickness | 0.75" Single Baffle |
| Finish | Dark Gray Trunkliner or Plush Black |
| Terminal Cup | Proline X ABS/Carbon Fiber, recessed mount, stainless hardware, copper ring terminals |
| Wiring | Pre-wired 12g OFC speaker wire |
| Polyfill | Installed |
| Built | Tullahoma, Tennessee |
| Warranty | 1-Year Limited on the enclosure |
| Brand + Model | Arc Audio X2V2 10 |
| Size | 10" |
| RMS Power | 200W |
| Peak Power | 400W |
| Voice Coil Config | Dual 2 ohm or Dual 4 ohm |
| Voice Coil Diameter | 2" |
| Xmax | 14.8mm one-way linear |
| Sensitivity | 85 dB |
| Frequency Response | 30–500 Hz |
| Cone Area (Sd) | 346 cm² |
| Mms | 129.05 g |
| Recommended Sealed Volume | 0.65 to 1.0 ft³ |
| Driver Warranty | 1-Year through Arc Audio |
Built From a Spec Sheet, Not a Sales Sheet
Every Proline X Performance Series enclosure is CNC-cut from Langboard Elite MDF, 3/4" (18mm) panels produced to published mill specifications. Most enclosure manufacturers source generic MDF without published data. We can tell you the internal bond rating, the modulus of elasticity, the modulus of rupture, and the face and edge screw holding strength for every panel in this enclosure, because we chose the material based on those numbers, not on price or availability.
Langboard Elite is produced in the United States. The specifications below are pulled directly from Langboard's published mill data and are verifiable. This is the same panel stock used in our full Proline X lineup.
Langboard Elite MDF: Published Mill Data
| Property | Value | Why It Matters |
|---|---|---|
| Panel Stock | Langboard Elite MDF | Named, verifiable panel source, not generic "high-density MDF" |
| Thickness | 3/4" (18mm) | Industry standard for subwoofer enclosures; panels below this flex under pressure |
| Density | 48.5 lbs/ft³ | Higher density = less porosity, better screw retention, reduced resonance |
| Internal Bond | 200 psi | Measures resistance to delamination under sustained internal pressure. The most enclosure-relevant spec on this sheet |
| Modulus of Rupture (MOR) | 4,200 psi | Bending strength before the panel breaks, relevant for larger unsupported baffle spans |
| Modulus of Elasticity (MOE) | 410,000 psi | Stiffness under load; higher MOE means less panel flex under bass pressure, less resonance |
| Face Screw Holding | 325 lbs | How firmly the panel surface holds a screw; critical for baffle joint integrity over time |
| Edge Screw Holding | 250 lbs | Panel edge retention, relevant for every joint that isn't face-to-face |
200 psi: The Number That Actually Matters for Enclosures
The internal bond rating measures how well the MDF panel resists delamination under sustained pressure applied perpendicular to the face. In a subwoofer enclosure, every bass transient generates a pressure pulse that pushes outward on every panel simultaneously. A panel that begins to delaminate internally loses stiffness gradually. The symptoms are slow: a box that starts to sound softer, less defined, less punchy over months of use. 200 psi internal bond is the spec that determines how long this enclosure holds its acoustic integrity under daily use at real power levels.
410,000 psi MOE: Less Flex, Less Resonance
The modulus of elasticity measures panel stiffness, its resistance to bending under load. A stiffer panel flexes less under the pressure generated by a high-excursion driver at volume. Panel flex is a source of acoustic coloration: the panel itself begins to radiate sound at its own resonant frequency, adding distortion to the output. 410,000 psi stiffness combined with V-groove and dado joinery means the panels stay rigid and the bracing controls resonance at the structure level, not the panel level. The bass you hear comes from the driver, not the box.
325 lb Face / 250 lb Edge: Joints That Stay Locked
Screw holding strength determines how firmly the panel grips a fastener at the face and at the edge. This matters most at the baffle joint, where the front panel meets the side panels and where the driver is mounted. A panel with low screw holding strength allows fasteners to loosen over time under vibration, leading to air gaps at the joint and loss of acoustic seal. 325 lb face screw holding strength means the baffle hardware stays put. Combined with dado joinery and adhesive, the front panel on a Proline X Performance Series enclosure is not going anywhere.
Named Panel Stock: Not "Premium MDF"
The phrase "premium MDF" or "high-density MDF" appears on marketing copy for enclosures across every price point, from $40 to $400. It is not a specification. It is a description with no defined standard. Langboard Elite is a named, sourced, mill-documented product with published data. We name it in our copy because naming it holds us accountable to the spec. You can look up Langboard Elite independently, verify the numbers on this page, and confirm you are getting what we say you are getting. That is the point.
Why Proline X?
Most enclosures are built to a price point. Proline X is built to a spec. Every box starts with published-data MDF, gets CNC-cut to exact internal volume, and is assembled by hand in our Tennessee facility. The difference shows up in the measurements — and in how the box holds up two years into daily use.
CNC-Cut to Spec
Panels are machine-cut on ShopSabre CNC routers and joined with V-groove and dado joinery. Consistent geometry, no hand-cut variance, no gaps at the joints.
Handcrafted in USA
Hand-assembled at our facility in Tullahoma, TN. Every enclosure is inspected before it ships.
Tuned to the Build
Internal volume and port geometry are calculated to spec and CNC-cut to exact dimensions. The box performs the same way every time.
Shop By Series
