Down-Fire Box Sizing: Single or Dual, 10 or 12 Inch
Most people start this decision at the wrong end. They pick a driver size, then go looking for a ...
Read Article →Proline X
SKU: Pro 12D-P FI NEO35 40x21
More enclosures cut for Fi Car Audio subwoofers: Fi Car Audio Subwoofer Boxes
A ported twelve inch box for a pair of Fi Car Audio NEO 3.5 12 in a 40 by 21 inch envelope, one shared chamber vented at 30.9 Hz
Special order, built for you. This cabinet is cut and built after you order it and ships within 15 working days of purchase.
This cabinet measures 7.17 cubic feet gross inside the walls and baffle. After the port, both braces and both woofers, two NEO 3.5 12 work against 4.41 cubic feet net, 2.2 cubic feet per woofer, vented at 30.9 Hz through a 78.0 square inch port. F3 lands at 26.4 Hz with 3.4 dB of passband lift above tuning. It measures 40.00 inches wide, 21.00 tall and 19.50 deep.
The NEO 3.5 12 is a 0.38 Qts driver with 34 mm of one-way Xmax, so it is happiest in a moderate chamber with a low tuning. The long port does double duty: it sets the tuning and it takes up the extra air a 40 by 21 cabinet would otherwise give a pair of twelves.
Threaded insert kit ships with this box. Fi Car Audio does not publish the mounting hole locations for the NEO 3.5 12, so we cannot install the threaded inserts before it ships. The threaded insert kit comes in the box instead: inserts sized to the woofer, the correct drill bit, 1.5 inch allen-head screws, an allen key and woofer gasket tape. You set the inserts when you mount the woofer, and this box ships with two kits, one per woofer.
Three layers of 3/4 inch Langboard Elite make a 2.25 inch front. The outer layer is routed to a 13.50 inch recess for each flange, so both woofers sit flush with the face; the two layers behind it carry the mounting hardware and the load.
A glossy black acrylic insert with the Fi Car Audio mark sits in the outer layer to the right of the woofers. It is standard on every Professional cabinet.
The 4.00 by 19.50 inch slot runs the full inside height on the left side, 16.75 inches back to the rear wall, then turns and runs 28.0 inches along the back wall behind both woofers, 44.75 inches of path in all. The mouth is cut with a 3/8 inch radius in all four corners, with a carpet groove 3/8 inch outside it so the carpet tucks clean around the opening.
Brace B1 runs from the baffle to the port wall between the woofers, tying the baffle, top, bottom and the rear port wall. Brace B2 runs the full depth from the baffle to the back wall on the right and forms the far side of the 4 inch port exit. Both are 3/4 inch MDF with four CNC-cut windows and 2 inch frames, set in dados. The port walls brace the left side and the full back of the box.
The port is sized so the mouth runs 16.3 meters per second RMS at 4800 W into the pair, under the 17 meters per second RMS guideline where a slot starts to chuff. All four mouth edges carry a 1/2 inch roundover.
Delivery to the 48 states is inside the price; it ships as a 117 lb parcel and checkout adds nothing. Special order: built after purchase and shipped within 15 working days.
40.00" W x 21.00" H x 19.50" D external, 7.17 cubic feet gross inside, 4.41 net. Both motors clear the rear port wall by 4.00 inches at the NEO 3.5 12's 10 inch mounting depth. The box ships dry: polyfill detunes a ported alignment.
Both drivers share one chamber and one port rather than sitting in separate boxes, so the pair works against the whole volume and the port is sized for the pair. Both drivers must be the same model and the same coil: mixing them puts unequal loads on one shared chamber, and neither driver sees the airspace it was picked for.
Set a 25 Hz subsonic filter, 24 dB per octave. Below tuning the vent stops loading the cone; with the filter in place the cone reaches about 20.4 mm of its 34 mm at 4800 W. Without the filter the pair reaches Xmax on about 3600 W, so on this box the filter is required.
| Series | Proline X Professional |
| Availability | Special Order | Ships Within 15 Working Days Of Purchase |
| Driver-Specific Fitment | Fi Car Audio NEO 3.5 12 D1/D2 (x2) |
| Enclosure Type | Ported | Front-Firing Standard Box |
| External Width | 40.00 Inches |
| External Height | 21.00 Inches |
| External Depth | 19.50 Inches |
| Internal Volume (Gross) | 7.17 Cubic Feet |
| Internal Volume (Net After Displacement) | 4.41 Cubic Feet (After Port, Bracing And Both Drivers) |
| Port Type | Vertical Slot On The Left | Front Exit | One 90 Degree Bend Along The Back Wall |
| Port Geometry | 4.00 x 19.50 Inches, 78.0 Square Inches, 44.75 Inches Of Path |
| Port Area | 78.0 Square Inches |
| Port Tuning (Fb) | 30.9 Hz |
| Port Mouth | R0.375 Corners (CNC), 1/2 In Roundover On All Four Edges, Carpet Groove 0.375 In Outside The Mouth |
| Port Air Velocity | 21.4 m/s In The Channel, 16.3 m/s At The Mouth, At 4800 W (17.0 m/s Chuff Threshold) |
| Design Power Basis | 4800 W RMS Into The Pair For Port Velocity And Excursion |
| Predicted F3 | 26.4 Hz (Anechoic) |
| Passband Ripple | 3.4 dB (Anechoic) |
| Subsonic Filter | 25 Hz High-Pass, 24 dB/Octave - REQUIRED On A Vented Enclosure |
| Driver Fs | 29.6 Hz |
| Driver Qts | 0.38 |
| Driver Vas | 26.11 Liters / 0.922 Cubic Feet |
| Driver Xmax | 34mm (One-Way) |
| Driver Displacement | 0.19 Cubic Feet |
| Driver Overall Diameter | 12.50 Inches |
| Mounting Depth Required | 10.00 Inches |
| Cutout Diameter | 11.125 Inches |
| Flush Mount Recess | 13.50 Inches In The Outer Layer |
| Material | Langboard Elite 3/4" MDF |
| Construction | ShopSabre CNC |
| Internal Bracing | B1: Center Windowed Brace, Baffle To Rear Port Wall, 11.75 x 19.50 | B2: Right Windowed Brace, Baffle To Back Wall, 16.50 x 19.50 | Four R0.375 Windows Each, 2.00 In Frames | Port Walls Brace The Left Side And Full Rear |
| Joinery | Dado Joinery (CNC-Cut), Flat Panels |
| Front Baffle Construction | Three 3/4" MDF layers, 2.25" total | Woofers Flush-Mounted In The Outer Layer |
| Baffle Layers | 3 |
| Acrylic | Glossy Black Fi Car Audio Logo Insert, Outer Layer, Standard |
| Mounting Hardware | Threaded Insert Kit Included (One Per Woofer): Inserts, Drill Bit, 1.5 In Allen-Head Screws, Allen Key, Gasket Tape |
| Terminal Cup | Proline X ABS/Carbon Fiber Composite | Back Panel | 12g OFC Pre-Wired |
| Damping | None - Ships Dry. Polyfill Detunes A Ported Enclosure |
| Carpet Finish | Plush Black |
| Shipping Weight | 117 lb |
| Shipping | UPS Ground Parcel, Included In The 48 States |
| Bundle Options | Enclosure Only (Bring Your Own Fi Car Audio NEO 3.5 12 x2) |
| Warranty | 2-Year Limited (Enclosure) |
| Manufactured | Tullahoma, Tennessee, USA |
Efficiency bandwidth product places the motor before anything else is decided.
7.17 cu ft gross, 4.41 cu ft net for the pair against a 26.1 L Vas per driver, vented at 30.9 Hz.
No sealed comparison is shown for this driver.
Travel scales with the square root of power, so there is one wattage that puts both cones exactly on Fi’s published 34.0 mm. The two traces are the same cabinet with the subsonic filter switched on and switched off. Every power figure in this section is for the pair, split evenly.
| Driver | Fi Car Audio NEO 3.5 12 |
| Coil Options | Dual 1 Ohm (D1) or Dual 2 Ohm (D2) |
| Motor | Neodymium |
| Fs | 29.6 Hz |
| Qts | 0.38 |
| Vas | 26.11 L (0.922 cu ft) |
| Xmax, One-Way | 34 mm |
| Mounting Depth | 10.00 in |
| Cutout Diameter | 11.125 in |
| Frame Outside Diameter | 12.50 in |
| Driver Displacement | 0.19 cu ft |
| Mounting Hole Locations | Not Published By Fi; Threaded Insert Kit Included |
Every Proline X Professional Series enclosure is CNC-cut from Langboard Elite MDF, 3/4" (18mm) panels produced to published mill specifications. Most enclosure manufacturers source generic MDF without published data. We can tell you the internal bond rating, the modulus of elasticity, the modulus of rupture, and the face and edge screw holding strength for every panel in this enclosure, because we chose the material based on those numbers, not on price or availability.
Langboard Elite is produced in the United States. The specifications below are pulled directly from Langboard's published mill data and are verifiable. This is the same panel stock used in our full Proline X lineup.
| Property | Value | Why It Matters |
|---|---|---|
| Panel Stock | Langboard Elite MDF | Named, verifiable panel source, not generic "high-density MDF" |
| Thickness | 3/4" (18mm) | Industry standard for subwoofer enclosures; panels below this flex under pressure |
| Density | 48.5 lbs/ft³ | Higher density = less porosity, better screw retention, reduced resonance |
| Internal Bond | 200 psi | Measures resistance to delamination under sustained internal pressure. The most enclosure-relevant spec on this sheet |
| Modulus of Rupture (MOR) | 4,200 psi | Bending strength before the panel breaks, relevant for larger unsupported baffle spans |
| Modulus of Elasticity (MOE) | 410,000 psi | Stiffness under load; higher MOE means less panel flex under bass pressure, less resonance |
| Face Screw Holding | 325 lbs | How firmly the panel surface holds a screw; critical for baffle joint integrity over time |
| Edge Screw Holding | 250 lbs | Panel edge retention, relevant for every joint that isn't face-to-face |
The internal bond rating measures how well the MDF panel resists delamination under sustained pressure applied perpendicular to the face. In a subwoofer enclosure, every bass transient generates a pressure pulse that pushes outward on every panel simultaneously. A panel that begins to delaminate internally loses stiffness gradually. The symptoms are slow: a box that starts to sound softer, less defined, less punchy over months of use. 200 psi internal bond is the spec that determines how long this enclosure holds its acoustic integrity under daily use at real power levels.
The modulus of elasticity measures panel stiffness, its resistance to bending under load. A stiffer panel flexes less under the pressure generated by a high-excursion driver at volume. Panel flex is a source of acoustic coloration: the panel itself begins to radiate sound at its own resonant frequency, adding distortion to the output. 410,000 psi stiffness combined with V-groove and dado joinery means the panels stay rigid and the bracing controls resonance at the structure level, not the panel level. The bass you hear comes from the driver, not the box.
Screw holding strength determines how firmly the panel grips a fastener at the face and at the edge. This matters most at the baffle joint, where the front panel meets the side panels and where the driver is mounted. A panel with low screw holding strength allows fasteners to loosen over time under vibration, leading to air gaps at the joint and loss of acoustic seal. 325 lb face screw holding strength means the baffle hardware stays put. Combined with dado joinery and adhesive, the front panel on a Proline X Professional Series enclosure is not going anywhere.
The phrase "premium MDF" or "high-density MDF" appears on marketing copy for enclosures across every price point, from $40 to $400. It is not a specification. It is a description with no defined standard. Langboard Elite is a named, sourced, mill-documented product with published data. We name it in our copy because naming it holds us accountable to the spec. You can look up Langboard Elite independently, verify the numbers on this page, and confirm you are getting what we say you are getting. That is the point.
Most enclosures are built to a price point. Proline X is built to a spec. Every box starts with published-data MDF, gets CNC-cut to exact internal volume, and is assembled by hand in our Tennessee facility. The difference shows up in the measurements, and in how the box holds up two years into daily use.
Panels are machine-cut on ShopSabre CNC routers and joined with V-groove and dado joinery. Consistent geometry, no hand-cut variance, no gaps at the joints.
Hand-assembled at our facility in Tullahoma, TN. Every enclosure is inspected before it ships.
Internal volume and port geometry are calculated to spec and CNC-cut to exact dimensions. The box performs the same way every time.








