Professional Series Ported 10" Enclosure | DD Audio 710g

DD publishes a Qts of 0.333 for the 710g, and computing it from their own Qes of 0.364 and Qms of 3.909 reproduces that figure exactly, so the driver's own numbers agree with each other. DD publish no vented recommendation for the 710g, so the 2.943 cubic foot net alignment and 32.5 Hz tuning come from our own solver working Fs, Qts and Vas against the coil's 1800 W rating. At 2160 W, 1.2 times that rating, the port mouth runs 16.6 m/s, closing in on the point where a slot starts to chuff; the margin here is narrow. Tuning is chosen for in-car response rather than an anechoic curve: a vehicle adds roughly 12 dB per octave below about 45 Hz, and this tuning is where that sum comes out flattest across 25 to 60 Hz.

Every driver is run through the Performance Optimized wedge and down-fire before this chassis; the Professional box is where a driver lands when that smaller envelope, 30 inches wide and 18 inches deep with a triangular side port, cannot give it what it needs at its rated power. The 710g did not clear the port gate there. The calmest wedge port that fits that envelope is 18.4 square inches at 23.5 by 12.00 by 16.91 inches, and its mouth runs 29.1 metres per second at 1800 W against the 17 metres per second line where a port starts to chuff. That port would stay clean to about 614 W. The slot on this box reaches 53.1 square inches and holds the mouth at 16.6 metres per second at 2160 W. An under-ported box does not fail quietly. Air speed at the mouth rises with power; past the chuff line the flow turns turbulent and the port is audible on every note. The turbulence also chokes the port, so the box behaves as if it were tuned higher than it is, loses output near tuning, and lets the cone travel further below tuning than the design allows. This chassis is a full-size front-firing box on a 2.25 inch baffle built from three 3/4 inch layers with the woofer flush-mounted in the outer layer, a DD Audio logo acrylic, and a port and excursion budget checked at 2160 W. It carries a 2 year warranty against 1.

DD Audio does not publish the mounting hole locations for the 710g, so we cannot install the threaded inserts before it ships. The threaded insert kit comes in the box instead: 8 to 12 inserts sized to the woofer, the correct drill bit, 2.5 inch allen-head screws, an allen key and woofer gasket tape. You set the inserts when you mount the woofer; one kit serves one woofer. A dual cabinet ships two kits.

Yes, at 26 Hz, 24 dB per octave. Below tuning a vented box stops loading the cone and excursion runs away toward DC. With the filter in place this cabinet puts the DD Audio 710g at 52 percent of its usable travel at 2160 W.

Not one we can show you. We do not build a sealed enclosure for the DD Audio 710g and DD Audio publish no sealed volume for it, so the Performance Graphs tab carries no ported-versus-sealed chart: the only sealed box left to plot would be this cabinet stuffed and sealed, which nobody would build, and a comparison against it would tell you nothing you could buy. What a vented box gives up is the region below tuning, where the cone unloads and the 26 Hz subsonic filter takes over; around 32.5 Hz the vent carries the load and cone travel drops to its minimum, which no sealed alignment can do.

It is a vertical slot beside the woofer, the full height of the cavity, 4.25 inches wide and 53.1 square inches. It runs 16.00 inches to the back wall and turns once along it for 10.75 inches; the fold costs about 1.5 Hz and the port is cut for it. The channel runs at 22.2 metres per second at 2160 W, 41 percent of its turbulence limit, and the mouth edges carry a 1/2 inch roundover so the air leaves the face at 16.6 metres per second against the 17 metres per second threshold where a slot starts to chuff.

65 lb, 30.00" W x 14.00" H x 24.00" D external. It ships as a UPS parcel; the price includes shipping in the 48 states. Every Professional cabinet is priced the same way, by its size: this one is 5.83 cubic feet outside. Delivery to the 48 states is inside the price; it ships as a 65 lb parcel and checkout adds nothing. The Performance Optimized 10 inch ported wedge is $369.99. The $221 difference is the larger box and the port this driver needs to run at its rating. Do not add polyfill; it ships dry on purpose.

No. This is an enclosure only, cut for the DD Audio 710g specifically: the 9.312 inch cutout, the 8.250 inch mounting depth allowance and the 2.94 cubic foot alignment all come from DD Audio's published parameters. It fits both coil versions; the alignment published here is the D2 or D4. Bring your own driver.