Stereo Integrity
Stereo Integrity HT-18 V3 | 18 Inch Home Theater Subwoofer
SKU: SI-HT18V3-D2
Stereo Integrity HT-18 V3 | 18 Inch Home Theater Subwoofer
New old stock, discontinued
Stereo Integrity HT-18 V3, 18 Inch Home Theater Subwoofer
Dual 2 ohm, 750 watts RMS, 25 mm of one-way travel and 1190 square centimeters of cone, in a 4 cubic foot sealed box. Brand new, never installed, and out of production.
- Discontinued
- Final sale
- Home theater
- Dual 2 ohm only
What You Are Buying
A Stereo Integrity HT-18 V3: an 18 inch home theater subwoofer driver, new in the box, from a run that ended years ago. Stereo Integrity keeps a reference page for it precisely because it is out of production, and that page is where the numbers below come from.
These are the last of them. There is no reorder.
Read this before you buy
Final sale. No returns, no exchanges and no warranty coverage. The HT-18 has been out of production for years, so a damaged driver cannot be matched or replaced. If you are building a pair or a quad, buy the count you need now rather than planning to add one later.
It Is Not the HST-18
The model numbers look close enough to cause trouble, so worth being direct about it. The HST-18 is Stereo Integrity's current 18, with a triple stacked motor, a carbon fiber cone and 40 mm of one-way travel. The HT-18 V3 is the older home theater driver and a genuinely different design.
Most of the price difference is that gap, not a discount on the same thing. Compare them on the parameters below rather than on the badge.
What the Parameters Tell You
A sealed driver, by design
Fs 23 Hz with a Qts of 0.59 and a Vas of 220 liters describes a driver built for a sealed box. The ratio of Fs to Qes, which is the usual shorthand for whether a driver prefers sealed or ported, comes out around 33, and anything in that region is telling you to seal it.
The 4 cubic foot recommendation, and what it actually does
Stereo Integrity specifies 4.0 cubic feet sealed. Running their published parameters through the standard sealed box math, that works out to a system Q around 1.01 with system resonance near 39 Hz.
That is a firm, slightly peaked alignment rather than a textbook flat one. In a room it is usually the right call, because room gain below 40 Hz fills in underneath the rolloff and the result sounds fuller than the raw curve suggests. Chasing a flat 0.707 alignment with this driver would take a box several times larger, which is why nobody builds one.
Excursion rather than brute power
25 mm of one-way linear travel across 1190 square centimeters of cone is a lot of air. That is why the 750 watt RMS rating is not the limitation you might expect from the number alone: the driver reaches high output by moving far, not by absorbing enormous power. Mms of 434 grams and a BL of 19.5 are consistent with that, a heavy cone with a motor strong enough to control it.
Specifications
| Size | 18 inch |
|---|---|
| Impedance | Dual 2 ohm, the only version built |
| Power handling | 750 watts RMS |
| Fs | 23 Hz |
| Qts / Qes / Qms | 0.59 / 0.69 / 4.11 |
| Re | 4.2 ohms |
| Le | 4.7 mH |
| Vas | 220 L |
| Sd | 1190 cm2 |
| Mms | 434 g |
| BL | 19.5 |
| Xmax | 25 mm one way |
| Sensitivity | 90.7 dB at 2.83 V |
| Recommended enclosure | 4.0 cubic feet sealed |
| Driver weight | 20 lb |
Mounting
The V3 technical drawing is included in the product images, and it is the thing to build to.
- Frame outer diameter 469.0 mm, which is 18.46 inches.
- Overall depth 268.5 mm, which is 10.57 inches.
- Basket depth below the flange 151.1 mm, with a 17.5 mm flange.
- Motor diameter 170.0 mm.
- Cut your baffle from the drawing, not from a figure retyped into a listing, including this one. An 18 inch driver is an expensive thing to discover you have cut a hole slightly wrong for.
Wiring the dual 2 ohm coils
Series gives you 4 ohms, parallel gives you 1 ohm. There was never a dual 4 ohm or dual 1 ohm HT-18, so if you see one advertised that way it is mislabeled. Check your amplifier is rated for whichever load you choose, particularly at 1 ohm.
Who This Suits
Buy this if
- You are building a home theater subwoofer and have room for 4 cubic feet sealed per driver.
- You want a lot of displacement for the money and do not need a warranty behind it.
- You are building more than one and can buy them all now.
- You are comfortable working from a technical drawing.
Look elsewhere if
- You need this in a car trunk. Four cubic feet is a truck, an SUV or a wall.
- You want warranty coverage or the option to return.
- You need a published frequency response or a voice coil diameter, neither of which Stereo Integrity published.
- You might want a matching driver later. There will not be one.
Installation Notes
- Brace the box. A 20 pound driver with 25 mm of travel will find every weak panel in a 4 cubic foot enclosure.
- Seal it properly. A sealed alignment only behaves as calculated if the box is actually airtight.
- Give the amplifier some headroom rather than running it at the limit. The driver reaches its output through excursion, so clean power matters more than maximum power.
- If you are running more than one, keep the boxes identical. Mismatched volumes between two drivers do more damage to the response than most people expect.
Condition and sale terms
New old stock of a discontinued Stereo Integrity driver. Never installed, never used. Sold as a final sale with no returns, no exchanges and no warranty coverage. Packaging may show shelf wear from storage. All specifications above are as published by Stereo Integrity on their HT-18 reference page and the V3 technical drawing; the sealed box behavior described is derived from those published parameters and labeled as such. Once these are gone this listing will be removed.
Questions on enclosure design, wiring or mounting before you buy: contact us.
| Re | 4.2 ohms |
|---|---|
| Fs | 23 Hz |
| Qes | 0.69 |
| Qms | 4.11 |
| Qts | 0.59 |
| Le | 4.7 mH |
| Sd | 1190 cm2 |
| Vas | 220 L |
| BL | 19.5 |
| Mms | 434 g |
| Xmax | 25 mm one way |
| Sensitivity | 90.7 dB at 2.83 V |
| Size | 18 inch |
|---|---|
| Impedance | Dual 2 ohm, the only configuration ever built |
| Power handling | 750 watts RMS |
| Recommended enclosure | 4.0 cubic feet sealed |
| Driver weight | 20 lb |
| Condition | New old stock, discontinued, final sale |
| Frame outer diameter | 469.0 mm (18.46 in) |
|---|---|
| Overall depth | 268.5 mm (10.57 in) |
| Basket depth below flange | 151.1 mm |
| Flange thickness | 17.5 mm |
| Motor diameter | 170.0 mm |
| Frequency response | Not published |
|---|---|
| Voice coil diameter | Not published |
| Displacement | Not published |
Figures come from Stereo Integrity's own HT-18 reference page and the V3 technical drawing, which is included in the product images. Cut your baffle to the drawing rather than to a number retyped from a listing.





