Maximizing Bass: The Essential Guide to Airspace for 6.5 ...
Welcome to the essential guide to airspace for 6.5 subwoofer boxes. If you're a bass enthusiast o...
Read Article →Proline X
SKU: PX-BRONCO-Q10S-TW3-1
More enclosures cut for JL Audio subwoofers: JL Audio Subwoofer Boxes
A custom downfire enclosure for four JL Audio 10TW3-D4 in a 42 by 17 inch footprint, two sealed chambers, 2.38 cubic feet net
Special order, built for you. This cabinet is cut and built after you order it and ships within 15 working days of purchase.
This box puts four 10 inch JL Audio 10TW3-D4 drivers into a 42 inch wide, 17 inch deep footprint at 9.3125 inches tall, 11.8125 inches with the feet. It holds 2.52 cubic feet gross and 2.38 net, split into two sealed chambers so every driver works against 0.60 cubic feet. That is a Qtc of 0.91 with an anechoic F3 of 40.2 Hz, and in a Bronco cabin the rolloff below that is largely filled in by cabin gain.
The 10TW3-D4 is a 0.62 Qts Thin-Line driver with 15.2 mm of travel and only 3.25 inches of mounting depth. JL Audio's own sealed recommendation is 0.50 cubic feet; at 0.60 cubic feet each this box runs a little larger, for a flatter Qtc of 0.91. The TW3 frame is a rounded square, 10.5 inches across the flats and 11.2 inches across the corner tabs, so the drivers are set with their flats to the front and back edges. That is what lets four of them fit a 17 inch deep baffle with 1/8 inch between frames.
Two drivers along the front and two along the back, staggered so four 11.2 by 10.5 inch frames fit a 42 inch by 17 inch baffle with 0.50 inch edges. The drivers surface-mount on a 1.50 inch double baffle, the bottom panel of the box.
A 3/4 inch center divider splits the box into two sealed chambers of 1.19 cubic feet net. Drivers 1 and 2 share the left chamber, 3 and 4 the right, and each chamber has its own terminal cup on the back wall so the pairs can be wired and fed independently.
Six 1.5 by 1.5 inch feet hold the baffle 2.50 inches off the floor. The cones fire into that gap and the bass comes out around all four sides of the box. The TW3 cones stay well clear of the floor at full excursion.
Each chamber has two 3/4 inch MDF window braces running front to back, one off the front wall and one off the back wall, set in the gap between the staggered drivers. Each brace is glued to the baffle, the top panel and its wall, with a 1.50 inch frame around an open window so air moves freely, and each stops 1/4 inch short of the woofer cutout. With the center divider, that ties the baffle, top and long front and back panels together in the middle of each chamber.
Delivery to the 48 states is inside the price and checkout adds nothing. Special order: built after purchase and shipped within 15 working days. The loaded option includes four JL Audio 10TW3-D4 drivers installed and wired.
The four 10TW3-D4 drivers are rated 400 W RMS each, 1600 W total, and that thermal rating is the ceiling. Mechanically they reach their 15.2 mm of travel on about 2300 W without a subsonic filter and about 2500 W with a 25 Hz filter, so travel is not the limit at rated power. A light layer of fill is fine in a sealed box.
| Series | Proline X Custom | Vehicle: Ford Bronco |
| Availability | Special Order | Ships Within 15 Working Days Of Purchase |
| Driver-Specific Fitment | JL Audio 10TW3-D4 (x4) | 400 W RMS Each | 15.2 mm Xmax | Dual 4 Ohm |
| Enclosure Type | Sealed | Downfire | Quad 10" |
| External Width | 42.00 Inches |
| External Depth | 17.00 Inches |
| External Height | 9.3125 Inches (11.8125 Inches With Feet) |
| Internal Volume (Gross) | 2.52 Cubic Feet |
| Internal Volume (Net After Displacement) | 2.38 Cubic Feet (After Drivers, Divider And Bracing) |
| Chambers | 2 Sealed Chambers, 1.19 Cubic Feet Net Each, 2 Drivers Per Chamber |
| Volume Per Driver | 0.60 Cubic Feet |
| System Qtc | 0.91 |
| Predicted F3 | 40.2 Hz (Anechoic) |
| Baffle | 1.50 In Double 3/4 MDF | Bottom Panel | Surface Mount, Staggered |
| Cutout Diameter | 9.625 In (JL Audio Spec) |
| Driver Spacing | Front Row At 5.75 In From Front Edge, Back Row At 11.25 In | Frame Flats Front And Back | Divider At Center |
| Internal Bracing | 3/4 In Center Divider (Dado Set) + 2 Front-To-Back 3/4 In MDF Window Braces Per Chamber, Baffle To Top |
| Motor Clearance | 5.31 In From Motor To Top Panel (3.25 In Mounting Depth) |
| Feet | 6x 1.5 x 1.5 x 2.5 In | 2.50 In Floor Gap |
| Terminal Cups | 2 (One Per Chamber), Back Panel, Pre-Wired |
| Material | Langboard Elite 3/4" MDF |
| Construction | ShopSabre CNC | Dado Joinery |
| Carpet Finish | Plush Black |
| Damping | Light Fill Recommended For Sealed (Optional) |
| Shipping Weight | 53 lb Enclosure Only | 94 lb Loaded (Est.) |
| Shipping | Included In The 48 States |
| Warranty | 2-Year Limited (Enclosure) |
| Manufactured | Tullahoma, Tennessee, USA |
Efficiency bandwidth product places the motor before anything else is decided.
2.52 cu ft gross, 2.38 cu ft net in two sealed chambers: 0.60 cu ft per driver against a 19.8 L Vas.
Why the layout is what it is.
Travel scales with the square root of power, so there is one wattage that puts all four cones on the published 15.2 mm. Power figures are for all four drivers, split evenly.
| Driver | JL Audio 10TW3-D4 |
| Coil | Dual 4 Ohm |
| Power Handling, Continuous | 400 W |
| Fs | 32.3 Hz |
| Qts | 0.620 |
| Qes / Qms | 0.656 / 11.350 |
| Vas | 19.82 L (0.700 cu ft) |
| Sd | 365 cm² (56.53 sq in) |
| Re | 9.036 Ohm (Coils In Series) |
| Efficiency | 82.10 dB SPL, 1W/1m |
| Xmax, One-Way | 15.2 mm (0.60 in), Voice Coil Overhang Method |
| Mounting Depth | 3.25 in |
| Mounting Hole Diameter | 9.625 in |
| Overall Diameter | 11.2 in Major / 10.5 in Minor |
| Bolt Hole Circle | 10.5 in |
| Magnet Diameter | 5.1 in |
| Driver Displacement | 0.019 cu ft |
| Net Weight | 10.1 lb |
Every Proline X Professional Series enclosure is CNC-cut from Langboard Elite MDF, 3/4" (18mm) panels produced to published mill specifications. Most enclosure manufacturers source generic MDF without published data. We can tell you the internal bond rating, the modulus of elasticity, the modulus of rupture, and the face and edge screw holding strength for every panel in this enclosure, because we chose the material based on those numbers, not on price or availability.
Langboard Elite is produced in the United States. The specifications below are pulled directly from Langboard's published mill data and are verifiable. This is the same panel stock used in our full Proline X lineup.
| Property | Value | Why It Matters |
|---|---|---|
| Panel Stock | Langboard Elite MDF | Named, verifiable panel source, not generic "high-density MDF" |
| Thickness | 3/4" (18mm) | Industry standard for subwoofer enclosures; panels below this flex under pressure |
| Density | 48.5 lbs/ft³ | Higher density = less porosity, better screw retention, reduced resonance |
| Internal Bond | 200 psi | Measures resistance to delamination under sustained internal pressure. The most enclosure-relevant spec on this sheet |
| Modulus of Rupture (MOR) | 4,200 psi | Bending strength before the panel breaks, relevant for larger unsupported baffle spans |
| Modulus of Elasticity (MOE) | 410,000 psi | Stiffness under load; higher MOE means less panel flex under bass pressure, less resonance |
| Face Screw Holding | 325 lbs | How firmly the panel surface holds a screw; critical for baffle joint integrity over time |
| Edge Screw Holding | 250 lbs | Panel edge retention, relevant for every joint that isn't face-to-face |
The internal bond rating measures how well the MDF panel resists delamination under sustained pressure applied perpendicular to the face. In a subwoofer enclosure, every bass transient generates a pressure pulse that pushes outward on every panel simultaneously. A panel that begins to delaminate internally loses stiffness gradually. The symptoms are slow: a box that starts to sound softer, less defined, less punchy over months of use. 200 psi internal bond is the spec that determines how long this enclosure holds its acoustic integrity under daily use at real power levels.
The modulus of elasticity measures panel stiffness, its resistance to bending under load. A stiffer panel flexes less under the pressure generated by a high-excursion driver at volume. Panel flex is a source of acoustic coloration: the panel itself begins to radiate sound at its own resonant frequency, adding distortion to the output. 410,000 psi stiffness combined with V-groove and dado joinery means the panels stay rigid and the bracing controls resonance at the structure level, not the panel level. The bass you hear comes from the driver, not the box.
Screw holding strength determines how firmly the panel grips a fastener at the face and at the edge. This matters most at the baffle joint, where the front panel meets the side panels and where the driver is mounted. A panel with low screw holding strength allows fasteners to loosen over time under vibration, leading to air gaps at the joint and loss of acoustic seal. 325 lb face screw holding strength means the baffle hardware stays put. Combined with dado joinery and adhesive, the front panel on a Proline X Professional Series enclosure is not going anywhere.
The phrase "premium MDF" or "high-density MDF" appears on marketing copy for enclosures across every price point, from $40 to $400. It is not a specification. It is a description with no defined standard. Langboard Elite is a named, sourced, mill-documented product with published data. We name it in our copy because naming it holds us accountable to the spec. You can look up Langboard Elite independently, verify the numbers on this page, and confirm you are getting what we say you are getting. That is the point.
Most enclosures are built to a price point. Proline X is built to a spec. Every box starts with published-data MDF, gets CNC-cut to exact internal volume, and is assembled by hand in our Tennessee facility. The difference shows up in the measurements, and in how the box holds up two years into daily use.
Panels are machine-cut on ShopSabre CNC routers and joined with V-groove and dado joinery. Consistent geometry, no hand-cut variance, no gaps at the joints.
Hand-assembled at our facility in Tullahoma, TN. Every enclosure is inspected before it ships.
Internal volume and port geometry are calculated to spec and CNC-cut to exact dimensions. The box performs the same way every time.








