Loaded Subwoofer Enclosure: What It Is and How to Pick One
A loaded enclosure is a box with the subwoofer already installed. The amplifier is not included...
Read Article →Arc Audio
SKU: ARC 1000.6 W/IPS8.8DSP
Arc Audio ARC Series Amplifiers
Six channels at 175 watts each into 4 or 2 ohms, every pair bridgeable to 350 watts, and the eight-channel IPS 8.8 DSP module already fitted in place of the analog input board. This is the configuration that turns a six-channel power amplifier into a complete processed front end: crossovers, equalization, signal delay and input mixing all live inside the amplifier.
All Six Channels
175W x 6
At 4 ohms or 2 ohms
Bridged Pairs
350W x 3
At 4 ohms, three bridged channels
Total Output
1,050W
Six channels combined
The ARC 1000.6 holds 175 watts per channel at both 4 ohms and 2 ohms, so a 2-ohm midbass pair does not cost you output the way it would on a fixed-rail design. Each pair of channels bridges into a single 4-ohm load at 350 watts, which means the same chassis can run six speakers, or four speakers plus a bridged subwoofer channel, or three bridged channels, without adding a second amplifier.
Arc Audio ships the ARC Series with an analog input board and sells the IPS 8.8 DSP module separately. This unit has the IPS 8.8 installed. The module is not an outboard processor sitting next to the amplifier and it is not a daughterboard hanging off the input stage. It physically replaces the analog input board inside the chassis, so you get a single box, a single power run, a single ground, and no processor-to-amplifier interconnect to pick up noise.
Fitting the module also changes what the amplifier accepts. The analog board takes a single pair of balanced inputs. With the IPS 8.8 in place the amplifier takes six analog input channels with a sensitivity range of 0.5 to 32 volts, which is wide enough to take a high-power factory amplifier output directly, and routes them through a signal mixer before they reach the output stage.
The IPS 8.8 is an eight-channel processor. It brings dual signal mixers for recombining a factory system's split bands back into a full-range signal, crossovers on every channel pair, precise signal delay for time alignment, and 248 bands of equalization. Up to four user presets can be stored, and with the optional manual trigger switches they can be changed without a laptop or a controller connected.
Every crossover, the bandpass sections, the front-end bypass and the bass boost are controlled from the ARC Audio DNA graphical interface rather than by pots on the chassis. That is the trade the ARC Series makes: nothing to knock out of adjustment once the panels go back on, and nothing to re-set by ear in a parking lot.
Arc Audio designed the ARC Series for premium source units that already have crossovers, and for DSP-controlled systems. In its analog form the ARC 1000.6 is deliberately a straight power amplifier. With the IPS 8.8 fitted, all of that filtering moves into the processor where it belongs, which is why this configuration suits a full active build better than a conventional amplifier with knobs on the end.
Plan the tune before the install. With the IPS 8.8 fitted there are no crossover controls on the chassis. Every filter, delay and equalization setting is made over USB from a Windows PC running ARC Audio DNA. Set the system up and save a preset before the amplifier goes somewhere you cannot reach the USB port.
The ARC Series uses a high-pressure die-cast aluminum heat sink with a rough-grain black anodized finish and CNC-machined accents. Cool air is drawn in through vents at both ends of the heat sink, passes over the power supply switching devices and the output devices, and exhausts through an opening on the front edge. A variable-speed ball-bearing fan does the work and an onboard micro-controller manages its speed, so the amplifier stays quiet until it actually needs airflow. Integrated mounting feet sit in the corners of the heat sink, and plastic hex-head trim caps finish the fasteners once it is mounted.
Every ARC Series amplifier carries Arc Audio's TAMB technology, which is patent pending. If the master clock and output switching frequency of the amplifier ever interferes with radio reception or a keyless entry system, or beats against another amplifier in the vehicle, the installer can move the master clock frequency of the power supply and output circuits in software. That is a real fix for a problem that normally ends with relocating wiring or living with the noise.
Supporting the same goal, low-impedance filter chokes on the power connections keep power supply switching artifacts from being radiated by the power wires, and ultra-low ESR capacitors sit on both sides of the power supply for clean delivery under heavy passages.
The balanced differential input stage rejects common electrical noise and accepts unbalanced RCA, balanced processor outputs, and speaker-level signals. Speaker-level input adapter plugs attenuate a factory amplifier's output to a usable level. Auto turn-on works by DC offset detection or signal detection on channels 1 and 2, so a dedicated remote wire is optional. For factory systems that need a replacement amplifier interface, the IPS 8.8 is compatible with iDatalink Maestro AR modules, which require the vehicle-specific replacement module, a T-harness and the ARC to iData signal harness adapter.
Installation summary: 15 3/8 x 6 3/8 x 2 1/4 in, Class D, 3 x 30A fusing on board, 8.0 to 17.1 volt operating range with the DSP start-stop compliant down to 4.5 volts, six balanced analog inputs at 0.5 to 32 volts, two DSP-controlled RCA outputs, USB-micro for tuning, variable-speed ball-bearing fan, remote turn-on pass through, compatible with the optional PSC and LR-2 external level controls either singly or together.
Audio Intensity is an authorized Arc Audio dealer. Every unit we sell is brand new current production with full manufacturer warranty coverage and lifetime tech support.
Audio Intensity ships the Arc Audio ARC 1000.6 fast from Tullahoma, Tennessee. Tell us your speakers, your impedances and whether you are running a factory head unit or an aftermarket source, and we will confirm the channel assignment and the DSP input mapping before you order.
Need two channels instead of six? The Arc Audio ARC 1000.2 shares the same ARC Series chassis and cooling with 500 watts per channel. Running a dedicated subwoofer amplifier? The Arc Audio X2 1100.1 delivers 1100 watts at 1 ohm. Contact Audio Intensity to spec the right combination.
| Arc Audio ARC 1000.6 with IPS 8.8 DSP Specifications | |
|---|---|
| Power Output (at 14.4V) | |
| Stereo at 4 Ohms | 175 Watts RMS x 6 |
| Stereo at 2 Ohms | 175 Watts RMS x 6 |
| Bridged at 4 Ohms | 350 Watts RMS x 3 |
| Total Rated Output | 1,050 Watts RMS |
| Bridgeable Speaker Outputs | Yes |
| Output Load Switch | Yes |
| Output Type | Class-D |
| Processing (IPS 8.8 DSP Installed) | |
| DSP Equipped | Yes, ARC Audio IPS 8.8, 8-channel |
| Equalization | 248 bands |
| Crossovers, All Channel Pairs | DNA GUI controlled |
| Bandpass Crossovers | DNA GUI controlled |
| Crossover Front-End Bypass | DNA GUI controlled |
| Bass Boost | DNA GUI controlled |
| Signal Delay | Yes, DNA GUI controlled |
| Signal Mixers | Dual |
| User Defined Presets | Up to 4 |
| Preset Control Without PC | Optional manual trigger switches, not included |
| Tuning Software | ARC Audio DNA, Windows PC |
| Inputs and Audio | |
| Frequency Response | 10 Hz to 30 kHz |
| Input Channels (Analog) | 6 |
| Input Channel Selection | DNA control, mixer |
| Input Type | Balanced, RCA or speaker level |
| Input Sensitivity | 0.5V to 32V |
| Input Impedance | 10k Ohms |
| Input Gain Type | Dedicated selection by channel pairs in the Input Mixer utility |
| Audio Output (RCA) | 2, DSP controlled |
| Auto-Sense Turn-On | Yes, signal and DC (BTL), uses Ch 1/2 analog inputs only |
| Control and Integration | |
| iDatalink Maestro AR Capable | Yes, requires vehicle replacement module, T-harness and ARC to iData signal harness adapter |
| Compatible External Level Control | PSC or LR-2, sold separately |
| Dual External Control | Yes, PSC and LR-2 simultaneously |
| DSP Integrated On/Off Timing | Turn-on output up to 40 ms, auto-sense hold up to 200 ms |
| External Amp Remote Turn-On Output | Adjustable 0.05 to 40 seconds |
| Remote Turn-On Pass Through | Yes, DSP controlled |
| USB Connection Type | USB-Micro |
| Power, Cooling and Physical | |
| Fuse Rating | 3 x 30 Amp, on board |
| Amplifier Operating Voltage | 8.0V to 17.1V |
| DSP Operating Voltage | 8V to 17.1V, start-stop compliant to 4.5V |
| Adjustable Class-D Switching Frequency | Yes, TAMB technology, patent pending |
| Cooling | Forced induction, variable-speed ball-bearing fan, micro-controller managed |
| Onboard Diagnostics | Thermal, under and over voltage, short and DC protection |
| Clip Warning Lights | Yes |
| Dimensions | 15 3/8 in (L) x 6 3/8 in (W) x 2 1/4 in (H) |
| Heat Sink | High-pressure die-cast aluminum, rough-grain black anodized with CNC-machined accents |
| Warranty | Manufacturer warranty through authorized Arc Audio dealers |
See every Arc Audio subwoofer box and enclosure, each cut for a specific Arc Audio driver.