Proline X
Gladen Sigma SSWX12 Dual Box: Sealed 12" Down Fire Enclosure
SKU: PO 12D-S DF SSWX
- Alignment: 1.00 cu ft net per chamber, 2.01 total (2.35 gross). Qtc 0.707, fc 45.2 Hz, F3 45.3 Hz anechoic
- Driver: Gladen Sigma SSWX12, 2 x 2 ohm, 800 W RMS, 15 mm Xmax linear, 6.78 in mounting depth
- Chassis: Down firing sealed, fixed 30 x 15 in platform, 13.19 in tall excluding standoffs
- Construction: Dual Chamber | Down-Firing Sealed | V-Groove/Dado | Double 1.5" Baffle | Threaded Insert Kit | Standoffs Included
Gladen Sigma SSWX12 Dual Box: Sealed 12" Down Fire Enclosure
Proline X Performance Optimized Down Fire Dual 12" Sealed
Cut direct fit for the Gladen Sigma SSWX12. 1.00 cu ft net per chamber, 2.01 total on the fixed 30 by 15 inch platform, 13.19 inches tall before standoffs.
Built Around the Gladen Sigma SSWX12
The SSWX12 sits in Gladen's SSWX line, the strong half of the SIGMA series: a glassfiber cone on a foam surround, an aluminium basket and aluminium coil former, a 65 mm dual 2 ohm voice coil, 15 mm of linear excursion and 800 watts RMS, on a 330 mm frame needing 172 mm (6.78 in) of mounting depth. Every Thiele-Small figure here is Gladen's own, measured with the coils in series, and it comes from two surfaces that agree: their SIGMA manual and their product page. Qes and Qms reproduce the printed Qts, and the printed compliance follows from Vas and cone area, so the set is internally consistent.
Gladen publish no bolt circle for the SIGMA drivers, so a threaded insert kit and stainless machine screws ship in the box rather than the inserts being pressed at the shop. They publish no basket displacement either, so 0.14 cu ft per driver is an estimate and the net volume carries it.
Two Fully Separate Chambers
A full-height divider seated in dados splits the cabinet into two sealed chambers of 1.00 cu ft each, so one driver's back pressure cannot modulate the other's cone. Each driver sees only its own air, and both chambers are cut to the same volume so the pair stays matched. One shared side-mounted terminal cup feeds both driver positions.
Net Volume, Not Gross
The 1.00 cu ft quoted above is net acoustic volume per chamber, measured after subtracting the brace, the divider where there is one, and the driver's own displacement. It is the figure you would type into a modelling program, not the raw box volume. Gross on this cabinet is 2.35 cu ft.
What the Alignment Actually Is
At 13.19 inches tall this cabinet is bound by airspace rather than motor clearance, which is why each chamber lands on 1.00 cu ft, the same volume the wedge for this driver holds, and reads the same Qtc 0.707. The motor clears the top panel with 5.66 inches to spare.
| Driver | Chamber | System Qtc | fc | F3 |
|---|---|---|---|---|
| SSWX12 (2 x 2 ohm) | 1.00 cu ft | Qtc 0.707 | 45.2 Hz | 45.3 Hz |
For reference, Gladen publish their own recommended sealed volumes for this driver, net of the driver's own volume:
| Gladen Box | Volume | System Qtc | fc | F3 |
|---|---|---|---|---|
| Compact | 20 L / 0.71 cu ft | Qtc 0.778 | 49.8 Hz | 45.7 Hz |
| Universal | 30 L / 1.06 cu ft | Qtc 0.698 | 44.6 Hz | 45.3 Hz |
| SQ | 42 L / 1.48 cu ft | Qtc 0.647 | 41.4 Hz | 45.6 Hz |
Down Fire Construction
The pair of drivers fires downward through the bottom baffle into the floor, and the cabinet stands on standoffs that set the gap the output passes through.
Double Baffle, Flush Recess
Two bonded 3/4 in MDF sheets at the driver face, 1.5 inches through, the outer layer machined as a flush recess to Gladen's 330 mm frame.
Side-Mounted Terminal Cup
One cup, side mounted and pre-wired with 12 gauge OFC to both driver positions. Square corners, no radii.
Standoffs Included
The 1.75 inch standoffs ship with the cabinet and set the floor gap. The 13.19 inch height above excludes them.
Motor Clearance and Orientation
The motor rises off the bottom baffle into the cavity, so clearance runs to the top panel rather than to a back wall. Here the 172 mm (6.78 in) motor leaves 5.66 inches above it. All three external dimensions are stated in the down fire position, 30 inches wide by 15 deep by 13.19 tall, and the height excludes the standoffs.
Power and Warranty
A matched pair of SSWX12 gives four 2 ohm coils, 1.8 ohm DC each. On one channel the sensible load is 2 ohms: each driver's own coils in series for 4 ohms, then the two drivers in parallel. All four in series gives 8 ohms. Do not wire all four in parallel, which is 0.5 ohms and almost nothing is stable there. Power handling is 800 watts RMS per driver, 1600 for the pair, so aim for roughly 1120 to 1600 watts total.
Cut and assembled in Tullahoma, Tennessee on our own CNC equipment. Finished in plush black carpet, polyfill wall lining installed in both chambers, standoffs and a threaded insert kit in the box. 1 year limited warranty. Enclosure only, the drivers are purchased separately. Call or text 931-563-5151.
Cut for the Driver, Not the Catalog
1.00 cu ft net per chamber, 2.01 total at Qtc 0.707, F3 45.3 Hz, on the 30 by 15 inch down fire platform. Built to order in Tennessee.
| Specification | Value |
|---|---|
| Series | Proline X Performance Optimized Down Fire |
| Compatible Driver | Gladen Sigma SSWX12 (2 x 2 ohm), quantity 2. Direct fit |
| Configuration | Dual 12 inch, two fully separate chambers sealed down fire |
| Mounting Position | Trunk or cargo floor, cone facing the floor |
| Firing Direction | Downward through the bottom baffle. Standoffs included |
| External Width | 30.00 in |
| External Depth | 15.00 in |
| External Height | 13.19 in, excluding the 1.75 in standoffs |
| Internal Volume, Gross | 2.35 cu ft total |
| Internal Volume, Net Acoustic | 1.00 cu ft per chamber, 2.01 cu ft total, after the divider and the driver displacement |
| Driver Mounting Depth | 6.78 in required (172 mm); 5.66 in clearance above the motor to the top panel |
| Alignment, SSWX12 (2 x 2 ohm) | Qtc 0.707, fc 45.2 Hz, F3 45.3 Hz anechoic, per chamber |
| Airspace Set By | Airspace. The cabinet is tall enough that volume binds before motor clearance |
| Floor Slot | 74 percent of one cone's area at the fixed 1.75 in standoff |
| Woofer Openings | Two, 11.15 in, cut for Gladen's 283 mm installation diameter |
| Frame Outer Diameter | 12.99 in (330 mm) |
| Bolt Circle | Not published by Gladen; threaded insert kit included |
| Driver Displacement | 0.14 cu ft each, estimated; Gladen publish none |
| Maker Recommended Sealed | 20 L Compact, 30 L Universal, 42 L SQ net per driver, Qtc 0.78 / 0.70 / 0.65 |
| Power Handling | 800 W RMS per driver, 1600 W for the pair |
| Recommended Wiring | Coils in series per driver, drivers in parallel, for a 2 ohm single channel load |
| Terminal Cup | One, side mounted, pre-wired with 12 gauge OFC |
| Baffle | Double layer, 1.5 in through, outer layer machined as a flush recess |
| Material | Langboard Elite MDF, 3/4 in |
| Covering | Plush black carpet |
| Damping | Polyfill wall lining installed in both chambers |
| Feet | 1.75 in standoffs included |
| Weight | 42 lb cabinet, 48 lb packed |
| Warranty | 1 year limited |
| Build Location | Tullahoma, Tennessee |
01Is it a sealed driver?
Efficiency bandwidth product places the motor before anything else is decided.
02What the box does to it
1.00 cu ft against a 28.4 L Vas.
03The watts that reach Xmax (in this enclosure)
Travel scales with the square root of power, so there is one wattage that puts the cone exactly on 15.0 mm — and a bigger one once a subsonic filter stops it wasting travel below the passband.
| Param | Value | Unit | Note |
|---|---|---|---|
| Fs | 32.00 | Hz | free-air resonance |
| Qts | 0.500 | 2 x 2 ohm | |
| Vas | 28.40 | L | equivalent compliance |
| Sd | 530.9 | cm² | effective piston area |
| Xmax | 15 | mm | linear, published as plus/minus 15 mm |
| Pe | 800 | W | continuous RMS |
| SPL | 84.3 | dB | 1 W / 1 m, derived from T/S |
Driver parameters as published by Gladen SIGMA subwoofer manual, SSWX12 column. Curves computed against this enclosure’s actual net airspace.
Built From a Spec Sheet, Not a Sales Sheet
Every Proline X Performance Series enclosure is CNC-cut from Langboard Elite MDF, 3/4" (18mm) panels produced to published mill specifications. Most enclosure manufacturers source generic MDF without published data. We can tell you the internal bond rating, the modulus of elasticity, the modulus of rupture, and the face and edge screw holding strength for every panel in this enclosure, because we chose the material based on those numbers, not on price or availability.
Langboard Elite is produced in the United States. The specifications below are pulled directly from Langboard's published mill data and are verifiable. This is the same panel stock used in our full Proline X lineup.
Langboard Elite MDF: Published Mill Data
| Property | Value | Why It Matters |
|---|---|---|
| Panel Stock | Langboard Elite MDF | Named, verifiable panel source, not generic "high-density MDF" |
| Thickness | 3/4" (18mm) | Industry standard for subwoofer enclosures; panels below this flex under pressure |
| Density | 48.5 lbs/ft³ | Higher density = less porosity, better screw retention, reduced resonance |
| Internal Bond | 200 psi | Measures resistance to delamination under sustained internal pressure. The most enclosure-relevant spec on this sheet |
| Modulus of Rupture (MOR) | 4,200 psi | Bending strength before the panel breaks, relevant for larger unsupported baffle spans |
| Modulus of Elasticity (MOE) | 410,000 psi | Stiffness under load; higher MOE means less panel flex under bass pressure, less resonance |
| Face Screw Holding | 325 lbs | How firmly the panel surface holds a screw; critical for baffle joint integrity over time |
| Edge Screw Holding | 250 lbs | Panel edge retention, relevant for every joint that isn't face-to-face |
200 psi: The Number That Actually Matters for Enclosures
The internal bond rating measures how well the MDF panel resists delamination under sustained pressure applied perpendicular to the face. In a subwoofer enclosure, every bass transient generates a pressure pulse that pushes outward on every panel simultaneously. A panel that begins to delaminate internally loses stiffness gradually. The symptoms are slow: a box that starts to sound softer, less defined, less punchy over months of use. 200 psi internal bond is the spec that determines how long this enclosure holds its acoustic integrity under daily use at real power levels.
410,000 psi MOE: Less Flex, Less Resonance
The modulus of elasticity measures panel stiffness, its resistance to bending under load. A stiffer panel flexes less under the pressure generated by a high-excursion driver at volume. Panel flex is a source of acoustic coloration: the panel itself begins to radiate sound at its own resonant frequency, adding distortion to the output. 410,000 psi stiffness combined with V-groove and dado joinery means the panels stay rigid and the bracing controls resonance at the structure level, not the panel level. The bass you hear comes from the driver, not the box.
325 lb Face / 250 lb Edge: Joints That Stay Locked
Screw holding strength determines how firmly the panel grips a fastener at the face and at the edge. This matters most at the baffle joint, where the front panel meets the side panels and where the driver is mounted. A panel with low screw holding strength allows fasteners to loosen over time under vibration, leading to air gaps at the joint and loss of acoustic seal. 325 lb face screw holding strength means the baffle hardware stays put. Combined with dado joinery and adhesive, the front panel on a Proline X Performance Series enclosure is not going anywhere.
Named Panel Stock: Not "Premium MDF"
The phrase "premium MDF" or "high-density MDF" appears on marketing copy for enclosures across every price point, from $40 to $400. It is not a specification. It is a description with no defined standard. Langboard Elite is a named, sourced, mill-documented product with published data. We name it in our copy because naming it holds us accountable to the spec. You can look up Langboard Elite independently, verify the numbers on this page, and confirm you are getting what we say you are getting. That is the point.
Why Proline X?
Most enclosures are built to a price point. Proline X is built to a spec. Every box starts with published-data MDF, gets CNC-cut to exact internal volume, and is assembled by hand in our Tennessee facility. The difference shows up in the measurements, and in how the box holds up two years into daily use.
CNC-Cut to Spec
Panels are machine-cut on ShopSabre CNC routers and joined with V-groove and dado joinery. Consistent geometry, no hand-cut variance, no gaps at the joints.
Handcrafted in USA
Hand-assembled at our facility in Tullahoma, TN. Every enclosure is inspected before it ships.
Tuned to the Build
Internal volume and port geometry are calculated to spec and CNC-cut to exact dimensions. The box performs the same way every time.
Shop By Series








