Proline X PO 10-S W SSWX sealed wedge, front baffle with gloss black insert and pre-wired leads, 13.6 by 13 inches.
Proline X PO 10-S W SSWX sealed wedge, side profile with recessed terminal cup, 12.6 inch base, 13 inches tall.
Proline X PO 10-S W SSWX sealed wedge, front baffle with gloss black insert and pre-wired leads, 13.6 by 13 inches.
Proline X PO 10-S W SSWX sealed wedge, side profile with recessed terminal cup, 12.6 inch base, 13 inches tall.

Proline X

Gladen Sigma SSWX10 Box: Sealed 10" Wedge Enclosure

SKU: PO 10-S W SSWX BB

QUICK SPECS
  • Best For: Gladen Sigma SSWX10 Trunk-Fit Daily Driver Builds
  • Net Volume: 0.46 cu ft (0.53 cu ft Gross)
  • Driver Match: Gladen Sigma SSWX10 (2 x 2 ohm)
  • Construction: Rear-Firing Wedge | V-Groove/Dado | Double 1.5" Baffle | Threaded Insert Kit
Shipping Icon
Shipping Included No freight charges at checkout. What you see is what you pay.
USA Flag Rounded
Built in Tennessee CNC cut from 3/4" Langboard Elite MDF. V-groove and dado joinery.
Tools icon: hands-on mobile audio expertise since 1985
Advanced Terminal Cup Built in-house. ABS/Carbon Fiber. Stainless steel hardware. Copper ring terminals.
$ 289.99
In Stock and Ready to Ship
Shop Pay Financing available. Choose Shop Pay Installments at checkout.
Proline X PO 10-S W SSWX sealed wedge, front baffle with gloss black insert and pre-wired leads, 13.6 by 13 inches.

Gladen Sigma SSWX10 Box: Sealed 10" Wedge Enclosure

Enclosure Type Sealed
External Dimensions 13.56" W x 13.00" H x 12.55" D at base tapering to 7.82" D at top
Gross Volume 0.53 cu ft
Net Volume 0.46 cu ft
Shipping Weight 22 lbs
Front Panel Thickness 1.5"
INSTALLER'S TAKE

0.46 cubic feet: Qtc 0.695 on the SSWX10, fc 43.9 Hz, F3 44.7 Hz.

The baffle set this one, not the airspace. Gladen's 281 mm frame will not sit on a cabinet narrow enough for a 0.707 box, so the width came first and the volume followed; the 5.98 inch motor still clears the raked back with 0.75 to spare.

One caveat on the data: Gladen's published Mms and Cms for this driver do not reconcile with their own Fs, so I have not used them for anything. Fs, Qts and Vas are what the box is built on and their own three sealed volumes back those up. Displacement is estimated, they publish none.

No bolt circle published, so the insert kit goes in when the driver is mounted. Sealed, so leave the polyfill as it is and keep it at 700 watts or under.

Product Details
Specifications
Performance Graphs
Customer Installs
Materials
Product Details

Performance Optimized Wedge | Gladen Sigma SSWX10

10" Sealed Wedge Enclosure | Rear-Firing Trunk-Load Design

0.46 ft3 Net0.53 ft3 GrossQtc 0.69Single Chamber Wedge13.56" x 13.00" x 7.82/12.55"Built in Tennessee

The Gladen Sigma SSWX10 in a Sealed Wedge

The SSWX10 sits in Gladen's SSWX line, the strong half of the SIGMA series: a glassfiber cone on a foam surround, an aluminium basket and aluminium coil former, a 65 mm (2.5 inch) dual 2 ohm voice coil, a 176 mm motor and a force factor of 21.0 Tm, rated 700 watts RMS with 15 mm of linear excursion, 152 mm (5.98 inch) of mounting depth on a 281 mm (11.06 inch) frame. Against the base SSW 10 it carries a larger coil, a bigger motor and more travel.

Every Thiele-Small figure here is Gladen's own, measured with the voice coils in series, and it comes from two surfaces that agree: their SIGMA subwoofer manual and their product page. Fs, Qts and Vas are the only parameters a sealed alignment uses, and Qes and Qms reproduce the printed Qts to within 1.3 percent. Gladen's published moving mass and compliance do not reconcile with the printed Fs on this driver, about 30 percent out whichever pair you solve from, and the compliance is printed to two significant figures. Those two figures are listed below for completeness, but no number on this page is derived from them: the alignment is corroborated instead by Gladen's own recommended sealed volumes, which all land in the 0.6 to 0.8 band.

0.46 cubic feet net on Gladen's published figures: the SSWX10 reads Qtc 0.695 with system resonance at 43.9 Hz and half power at 44.7 Hz. That is essentially the Butterworth alignment: maximally flat, neither peaking at resonance nor drying the bottom end out. Gladen's own recommended sealed volumes for this driver are 10 litres Compact at Qtc 0.74, 16 litres Universal at Qtc 0.66, 23 litres SQ at Qtc 0.61, so this cabinet sits in the same family.

Trunk-Load Wedge Design Explained

The driver mounts on the vertical trunk-lid-side face and fires rearward into the trunk cavity.

Seat-Side Face Matches Seat Lean

Angled face matches the roughly 20 degree factory seat lean.

Trunk-Lid-Side Face Fires the Woofer

Vertical baffle, cone firing rearward into the trunk cavity.

Trunk Cavity Loading

The trunk acts as an acoustic extension for a smoother presentation.

Preserves Trunk Cargo Space

The wedge tucks against the seat back and the space in front stays usable.

Engineered for the Gladen Sigma SSWX10

Anechoic half power lands at 44.7 Hz, before any cabin gain. Gladen publish no driver displacement, so an estimated 0.06 cubic feet is taken out of the net figure. Their own recommended volumes are quoted net of the driver, which makes them directly comparable to the 0.46 cubic feet on this page.

Alignment Numbers

Driver System Qtc fc F3
SSWX10 (2 x 2 ohm) Qtc 0.695 43.9 Hz 44.7 Hz

Why This Airspace

Gladen's 281 mm frame needs a wider baffle than a 0.707 alignment wants on this chassis, so the width that carries the flange sets the airspace rather than the other way round. The cabinet is therefore larger than the 0.43 cu ft a Butterworth box would use, and the Qtc printed here is the one it actually lands on.

Gladen's Own Sealed Recommendations

Gladen Box Volume System Qtc fc F3
Compact 10 L / 0.35 cu ft Qtc 0.745 47.1 Hz 44.9 Hz
Universal 16 L / 0.57 cu ft Qtc 0.661 41.8 Hz 44.9 Hz
SQ 23 L / 0.81 cu ft Qtc 0.614 38.8 Hz 45.6 Hz

Mounting Geometry

The baffle is cut to 9.13 in for Gladen's 232 mm installation diameter, and the 281 mm (11.06 in) frame lands about 0.96 in of flange on every side of the hole. The rear panel rakes 20 degrees, so the cavity deepens from 7.82 in at the top to 12.55 in at the base, and the 152 mm (5.98 in) motor clears it with 0.75 in to spare. Gladen publish no bolt circle for the SIGMA drivers, so a threaded insert kit and stainless machine screws ship in the box rather than the inserts being pressed at the shop.

What the Numbers Rest On

Langboard Elite MDF

Premium 3/4 in MDF throughout.

V-Groove and Dado Joinery

CNC cut V-grooves at every panel intersection, sides and brace seated in dados.

Double-Layer 1.5" Front Baffle

Two bonded 3/4 in MDF sheets at the driver face, the outer layer machined as a flush recess.

Gladen's Published Parameters

SSWX10 (2 x 2 ohm): Fs 31 Hz, Qts 0.49, Qes 0.52, Qms 6.96, Vas 13.1 L, Mms 258.7 g, Cms 0.06 mm/N, Bl 21.0 Tm, Re 1.8 ohm per coil. Cone area 366.5 cm2. Xmax 15 mm (linear, published as plus or minus). Sensitivity 86.5 dB at 2.83 V / 1 m.

Wiring the Gladen Sigma SSWX10 to Your Amplifier

Gladen build the SSWX10 in one version, 2 x 2 ohm: two 2 ohm coils measuring 1.8 ohm DC each, 4 ohms nominal in series or 1 ohm nominal in parallel. Series to 4 ohms is the safe default; run the 1 ohm parallel load only on an amplifier rated 1 ohm stable. Confirm the final load against your amplifier's minimum stable impedance before powering the system.

Power handling is 700 watts RMS, 1400 watts peak. Aim for roughly 489 to 700 watts at the impedance you wire.

Built in Tennessee, Backed by Audio Intensity

Cut and assembled in Tullahoma, Tennessee on our own CNC equipment. Finished in plush black carpet with the gloss black acrylic baffle insert, one side-mounted pre-wired terminal cup, 12 gauge OFC to the driver position. Polyfill wall lining installed. Threaded insert kit and stainless machine screws included (Gladen publishes no bolt circle). 1 year limited warranty. Enclosure only, the driver is purchased separately. Call or text 931-563-5151.

Gladen Sigma SSWX10: Cut for One Driver

0.46 cubic feet net at Qtc 0.69, F3 44.7 Hz, cut direct fit and built to order in Tennessee.

Specifications
SpecificationValue
SeriesProline X Performance Optimized Wedge
Compatible DriverGladen Sigma SSWX10 (2 x 2 ohm), quantity 1. Direct fit
ConfigurationSingle 10 inch, single chamber sealed wedge
Mounting PositionTrunk or cargo area, tall face against the rear seat back
Firing DirectionRearward into the trunk. Not a down fire design, no feet included
External Width13.56 in
External Height13.00 in at the seat face
External Depth12.55 in at the base, tapering to 7.82 in at the top
Internal Volume, Gross0.53 cu ft
Internal Volume, Net Acoustic0.46 cu ft after the brace and the driver displacement
Driver Mounting Depth5.98 in required (152 mm); 0.75 in clearance above the motor against the raked rear panel
Alignment, SSWX10 (2 x 2 ohm)Qtc 0.695, fc 43.9 Hz, F3 44.7 Hz anechoic
Airspace Set ByThe baffle. Gladen's 281 mm frame needs a wider cabinet than a 0.707 alignment would use, so the flange sets the width and the width sets the volume
Woofer Opening9.13 in, cut for Gladen's 232 mm installation diameter
Frame Outer Diameter11.06 in (281 mm)
Bolt CircleNot published by Gladen; threaded insert kit included
Driver Displacement0.06 cu ft, estimated; Gladen publish none for this model
Maker Recommended Sealed10 L Compact, 16 L Universal, 23 L SQ net, Qtc 0.74 / 0.66 / 0.61
Terminal CupOne, side mounted, pre-wired with 12 gauge OFC
BaffleDouble layer, 1.5 in through, outer layer machined as a flush recess
MaterialLangboard Elite MDF, 3/4 in
CoveringPlush black carpet
DampingPolyfill wall lining installed
Weight17 lb cabinet, 22 lb packed
Warranty1 year limited
Build LocationTullahoma, Tennessee
Performance Graphs
Net airspace
0.46
cu ft net
System Qtc
0.69
sealed
Half power
44.7
Hz · F3
Xmax at
713
W RMS · no filter
With 25 Hz subsonic
1013
W RMS · +42%
Amplifier
489-700
W RMS recommended
This enclosure holds 0.46 cu ft net . In it the Gladen SSWX10 runs a system Qtc of 0.69 with half power at 44.7 Hz, and the cone reaches its 15.0 mm travel limit at 713 W, above the driver’s 700 W thermal rating, so heat stops you before travel does. Run a subsonic filter at 25 Hz and that becomes 1013 W — +300 W, or 42 percent more power for the same 15.0 mm of travel.

01Is it a sealed driver?

Efficiency bandwidth product places the motor before anything else is decided.

EBP = Fs ÷ Qes = 59.6
SEALED 0–50 TRANSITION 50–100 PORTED 100–150 0 50 100 150 2 x 2 ohm 59.6
2 x 2 ohm · EBP 59.6
At 59.6 the SSWX10 sits in the transition band, not the sealed band. That is not a mismatch: a transition motor works in either alignment, and sealed buys a smaller box and a gentler roll-off at the cost of some low-end output. Stage 02 shows what this airspace actually does with it.

02What the box does to it

0.46 cu ft against a 13.1 L Vas.

α = Vas ÷ Vb = 1.01  ·  Fc = Fs√(α+1) = 44 Hz  ·  Qtc = 0.69
20 30 50 70 100 150 200 +6 +0 -6 -12 -18 -24 FREQUENCY · Hz LEVEL · dB −3 dB
2 x 2 ohm · Qtc 0.69, Fc 44 Hz, F3 44.7 Hz
The box lifts resonance from 31.0 Hz free-air to 44 Hz and half power lands at 44.7 Hz, anechoic, before any cabin gain. Parameters are Gladen's own published figures, taken from the SIGMA subwoofer manual (document GLADEN-SIGMA-SUB-BA-001, Revision A) and cross-checked against Gladen's product page. Gladen measure the set with the voice coils in series. Fs, Qts and Vas are the only parameters a sealed alignment uses, and Qes and Qms reproduce the printed Qts to within 1.3 percent. Gladen's published moving mass and compliance do NOT reconcile with the printed Fs for this driver, about 30 percent out whichever pair you solve from, and the compliance is printed to two significant figures; those two figures are reproduced below for completeness but no number on this page is derived from them. The alignment is corroborated instead by Gladen's own three recommended sealed volumes. Gladen publish those volumes net of the driver's own volume: 10 litres Compact, 16 litres Universal, 23 litres SQ, which land on Qtc 0.74, Qtc 0.66, Qtc 0.61. This cabinet holds 0.46 cu ft net and reads Qtc 0.695. Gladen's 281 mm frame needs a wider baffle than a 0.707 alignment would want on this chassis, so the width that carries the flange sets the airspace rather than the other way round, and the figure plotted here is the one it actually lands on. Gladen publish no basket displacement, so 0.06 cu ft is estimated and the net volume carries that estimate. The driver is built in one coil configuration only, 2 x 2 ohms, so a single alignment covers every unit.

03The watts that reach Xmax (in this enclosure)

Travel scales with the square root of power, so there is one wattage that puts the cone exactly on 15.0 mm — and a bigger one once a subsonic filter stops it wasting travel below the passband.

PXmax = 713 W unfiltered  →  1013 W with a 25 Hz subsonic
20 30 50 70 100 150 200 0 4 8 12 16 FREQUENCY · Hz CONE TRAVEL · mm PAST LINEAR TRAVEL · Xmax 15.0 mm 713 W reaches Xmax here
2 x 2 ohm · 713 W, no filter2 x 2 ohm · 1013 W with subsonic at 25 Hz, 24 dB/octXmax 15.0 mm one-way
Every trace touches the limit and no further, because each is drawn at the exact power that puts that coil on 15.0 mm. Unfiltered that is 713 W, reached first at 20 Hz. It sits above the 700 W the driver can take thermally, so the voice coil gives up before the suspension does. The dashed traces are the same driver behind a subsonic filter at 25 Hz, 24 dB/oct: stopping the cone wasting travel below the passband lets it take 1013 W before hitting the same 15.0 mm. That is 42 percent more amplifier for the price of one filter setting.
ParamValueUnitNote
Fs31.00Hzfree-air resonance
Qts0.4902 x 2 ohm
Vas13.10Lequivalent compliance
Sd366.5cm²effective piston area
Xmax15mmlinear, published as plus/minus 15 mm
Pe700Wcontinuous RMS
SPL80.6dB1 W / 1 m, derived from T/S

Driver parameters as published by Gladen SIGMA subwoofer manual, SSWX10 column. Curves computed against this enclosure’s actual net airspace.

Customer Installs
Materials
Material

Built From a Spec Sheet, Not a Sales Sheet

Every Proline X Performance Series enclosure is CNC-cut from Langboard Elite MDF, 3/4" (18mm) panels produced to published mill specifications. Most enclosure manufacturers source generic MDF without published data. We can tell you the internal bond rating, the modulus of elasticity, the modulus of rupture, and the face and edge screw holding strength for every panel in this enclosure, because we chose the material based on those numbers, not on price or availability.

Langboard Elite is produced in the United States. The specifications below are pulled directly from Langboard's published mill data and are verifiable. This is the same panel stock used in our full Proline X lineup.

Specifications

Langboard Elite MDF: Published Mill Data

Property Value Why It Matters
Panel Stock Langboard Elite MDF Named, verifiable panel source, not generic "high-density MDF"
Thickness 3/4" (18mm) Industry standard for subwoofer enclosures; panels below this flex under pressure
Density 48.5 lbs/ft³ Higher density = less porosity, better screw retention, reduced resonance
Internal Bond 200 psi Measures resistance to delamination under sustained internal pressure. The most enclosure-relevant spec on this sheet
Modulus of Rupture (MOR) 4,200 psi Bending strength before the panel breaks, relevant for larger unsupported baffle spans
Modulus of Elasticity (MOE) 410,000 psi Stiffness under load; higher MOE means less panel flex under bass pressure, less resonance
Face Screw Holding 325 lbs How firmly the panel surface holds a screw; critical for baffle joint integrity over time
Edge Screw Holding 250 lbs Panel edge retention, relevant for every joint that isn't face-to-face
Internal Bond

200 psi: The Number That Actually Matters for Enclosures

The internal bond rating measures how well the MDF panel resists delamination under sustained pressure applied perpendicular to the face. In a subwoofer enclosure, every bass transient generates a pressure pulse that pushes outward on every panel simultaneously. A panel that begins to delaminate internally loses stiffness gradually. The symptoms are slow: a box that starts to sound softer, less defined, less punchy over months of use. 200 psi internal bond is the spec that determines how long this enclosure holds its acoustic integrity under daily use at real power levels.

Stiffness

410,000 psi MOE: Less Flex, Less Resonance

The modulus of elasticity measures panel stiffness, its resistance to bending under load. A stiffer panel flexes less under the pressure generated by a high-excursion driver at volume. Panel flex is a source of acoustic coloration: the panel itself begins to radiate sound at its own resonant frequency, adding distortion to the output. 410,000 psi stiffness combined with V-groove and dado joinery means the panels stay rigid and the bracing controls resonance at the structure level, not the panel level. The bass you hear comes from the driver, not the box.

Screw Holding

325 lb Face / 250 lb Edge: Joints That Stay Locked

Screw holding strength determines how firmly the panel grips a fastener at the face and at the edge. This matters most at the baffle joint, where the front panel meets the side panels and where the driver is mounted. A panel with low screw holding strength allows fasteners to loosen over time under vibration, leading to air gaps at the joint and loss of acoustic seal. 325 lb face screw holding strength means the baffle hardware stays put. Combined with dado joinery and adhesive, the front panel on a Proline X Performance Series enclosure is not going anywhere.

Sourcing

Named Panel Stock: Not "Premium MDF"

The phrase "premium MDF" or "high-density MDF" appears on marketing copy for enclosures across every price point, from $40 to $400. It is not a specification. It is a description with no defined standard. Langboard Elite is a named, sourced, mill-documented product with published data. We name it in our copy because naming it holds us accountable to the spec. You can look up Langboard Elite independently, verify the numbers on this page, and confirm you are getting what we say you are getting. That is the point.

Why Proline X?

Most enclosures are built to a price point. Proline X is built to a spec. Every box starts with published-data MDF, gets CNC-cut to exact internal volume, and is assembled by hand in our Tennessee facility. The difference shows up in the measurements, and in how the box holds up two years into daily use.

CNC-Cut to Spec

CNC-Cut to Spec

Panels are machine-cut on ShopSabre CNC routers and joined with V-groove and dado joinery. Consistent geometry, no hand-cut variance, no gaps at the joints.

Handcrafted in USA

Handcrafted in USA

Hand-assembled at our facility in Tullahoma, TN. Every enclosure is inspected before it ships.

Tuned to the Build

Tuned to the Build

Internal volume and port geometry are calculated to spec and CNC-cut to exact dimensions. The box performs the same way every time.

Frequently Asked Questions

Does this fit the Gladen Sigma SSWX10, and will any other 10 inch fit?

Why 0.46 cubic feet, and what alignment does it target?

What amplifier power should I run, and how should I wire it?

Why the wedge angle, and why rear-firing into the trunk?

Why is the front baffle double-layered?

What is the expected low-frequency extension?

Do I need to add polyfill or damping?

Is the driver included, and are the threaded inserts installed?

Related Articles