Proline X
Dayton Audio Max-X MX15-22 Box: Sealed 15" Wedge Enclosure | 20.5" W x 13.5" H
SKU: PO 15-S WDG MX1522 20.5x13.5
- Lead time: Special order, ships within 15 working days of purchase
- Alignment: 2.77 cu ft gross, 2.44 cu ft net sealed. Qtc 0.71, Fc 38.3 Hz, F3 38.4 Hz anechoic
- Driver: Dayton Audio Max-X MX15-22 (dual 2 ohm), 800 W RMS, 19 mm Xmax, 9.13 in mounting depth
- Build: Wedge with the woofer on a 21.8 degree slope, 1.5" double baffle, 1/4" motor pocket milled in the floor, threaded inserts installed, two front-to-back windowed braces, carpet groove on both side panels
- Cabinet: 20.5" W x 13.50" H x 27.00" D, 7.50" tall at the front, 12.00" flat top
Dayton Audio Max-X MX15-22 Box: Sealed 15" Wedge Enclosure | 20.5" W x 13.5" H
More enclosures cut for Dayton Audio subwoofers: Dayton Audio Subwoofer Boxes
Proline X 15" Sealed Wedge
A sealed wedge for one Dayton Audio Max-X MX15-22 on a 20.5 by 27 inch footprint, the woofer angled up 21.8 degrees on a doubled baffle
Special order, built for you. This cabinet is cut and built after you order it and ships within 15 working days of purchase.
Why 2.44 cubic feet
This cabinet measures 2.77 cubic feet gross inside the walls and the doubled baffle. After both braces and the woofer, the MX15-22 works against 2.44 cubic feet net, which on Dayton's published parameters gives a system Qtc of 0.71, resonance at 38.3 Hz and half power at 38.4 Hz: maximally flat, with no lift near resonance. The wedge holds the 27 inch depth and the 13.50 and 7.50 inch heights, and the width is set at 20.5 inches to land on that volume with both braces inside.
What goes into it
Wedge profile, angled baffle
The cabinet is 13.50 inches tall at the back and 7.50 at the front, with a 12 inch flat top. The woofer sits on the 16.16 inch slope between them, tilted 21.8 degrees, so the box fits behind or under a seat where a square cabinet will not.
Doubled 1.5 inch baffle
Two bonded 3/4 inch layers make up the sloped face. A single layer flexes under a 15 inch woofer at 800 watts; the second one stiffens the face and gives the mounting hardware twice the material to bite. The 14.01 inch cutout runs through both.
Motor pocket in the floor
On the slope the low edge of the MX15-22's 180 mm magnet comes down to the floor. We mill a 1/4 inch pocket, 2 by 6.5 inches, into the inside of the bottom panel under it, which leaves 0.20 inch of clearance and 1/2 inch of MDF beneath.
Threaded inserts installed
Dayton publishes the MX15-22's 14.65 inch bolt circle, so the inserts are pressed at the shop and the driver bolts straight in with the stainless machine screws included.
Two front-to-back braces
B1 and B2 run the full depth of the box, 4.625 to 5.375 inches either side of center, splitting the width into thirds. Each is cut to the wedge profile, notched to clear the cone and threaded inserts by 1/2 inch, and opened up to about half open air with 1.5 inch webs, two vertical bars and three large CNC-cut windows, set in dados that tie the front, the baffle, the floor, the top and the back wall together. The motor passes between them.
Carpet groove on both sides
The outside face of each side panel carries a routed groove 3/4 inch in from every edge, following the wedge profile, so the carpet tucks in tight and the side edges stay crisp.
Terminal cup
One Proline X ABS and carbon fiber terminal cup sits on the back panel, pre-wired with 12 gauge OFC.
Special order
This cabinet is cut and built after you order it and ships within 15 working days of purchase.
The cabinet
20.5" W x 13.50" H x 27.00" D external, 7.50 inches tall at the front, with a 12.00 inch flat top. 2.77 cubic feet gross inside, 2.44 net after two windowed braces and the woofer. The 9.13 inch motor sits 1.27 inches above the floor at its center, and the pocket under its low edge keeps the whole magnet clear. A light polyfill wall lining controls internal reflections without changing the acoustic volume.
The numbers to respect
Unfiltered, the cone reaches its 19 mm Xmax at 775 W, just under the driver's 800 W rating. Set a 25 Hz subsonic filter, 24 dB per octave, and that rises to 1218 W, so the 800 W the voice coil can take becomes the limit instead of travel.
| Series | Proline X Performance Optimized |
| Availability | Special Order | Ships Within 15 Working Days Of Purchase |
| Driver-Specific Fitment | Dayton Audio Max-X MX15-22 (dual 2 ohm), quantity 1. Direct fit |
| Enclosure Type | Sealed | Wedge, Woofer On A 21.8 Degree Sloped Baffle |
| External Width | 20.50 Inches |
| External Height | 13.50 Inches At The Back, 7.50 Inches At The Front |
| External Depth | 27.00 Inches At The Base, 12.00 Inch Flat Top |
| Sloped Baffle | 16.16 Inches Long At 21.8 Degrees |
| Internal Volume (Gross) | 2.77 Cubic Feet |
| Internal Volume (Net After Displacement) | 2.44 Cubic Feet (After Both Braces And The Driver) |
| Alignment, MX15-22 | Qtc 0.71, Fc 38.3 Hz, F3 38.4 Hz Anechoic |
| Power To Reach Xmax | 775 W Unfiltered | 1218 W With A 25 Hz, 24 dB/Octave Subsonic |
| Woofer Opening | 14.01 Inches, Through Both Baffle Layers |
| Frame Outer Diameter | 15.42 Inches |
| Bolt Circle | 14.65 Inches, Dayton Spec; Threaded Inserts Pre-Installed |
| Mounting Depth Required | 9.13 Inches (232 mm) |
| Motor Clearance | 1.27 Inches At The Magnet Center | 0.20 Inch At The Low Edge Of The 180 mm Magnet, Over A 1/4 Inch Floor Pocket |
| Floor Pocket | 1/4 Inch Deep, 2 x 6.5 Inches, 7 To 9 Inches Back From The Front, Centered | 1/2 Inch MDF Remains |
| Driver Displacement | 0.22 Cubic Feet (6.3 L, Calculated) |
| MX15-22 Fs / Qts / Qes / Qms / Vas | 21.7 Hz / 0.40 / 0.46 / 4.27 / 146 L |
| Driver Sd | 820 cm2, Dayton Spec |
| Xmax | 19 mm, One-Way, As Dayton Publish It |
| Driver Power Handling | 800 W RMS |
| Wiring Options | Dual 2 ohm: 4 Ohms In Series Or 1 Ohm In Parallel. Series To 4 Ohms Is The Safe Default |
| Material | Langboard Elite 3/4" MDF |
| Construction | CNC Cut, Dado Joinery |
| Panel Thickness | 0.75 Inches |
| Front Baffle | 1.5 Inch Double Baffle, Two 3/4" Layers |
| Internal Bracing | B1 And B2: Two Windowed Braces, Front To Back, 4.625 To 5.375 In Either Side Of Center | Full Wedge Profile, Notched To Clear The Woofer And Inserts By 0.50 In | About 51% Open: 1.50 In Webs, Two Vertical Bars, Three Windows | Set In Dados |
| Carpet Groove | Routed Into The Outside Face Of Both Side Panels, 0.75 In In From Every Edge |
| Terminal Cup | Proline X ABS/Carbon Fiber Composite | Back Panel | 12g OFC Pre-Wired |
| Damping | Light Polyfill Wall Lining, Does Not Alter Acoustic Volume |
| Carpet Finish | Plush Black |
| Bundle Options | Enclosure Only (Bring Your Own Dayton Audio MX15-22) |
| Warranty | 1-Year Limited (Enclosure) |
| Manufactured | Tullahoma, Tennessee, USA |
01Is it a sealed driver?
Efficiency bandwidth product places the motor before anything else is decided.
02What the box does to it
2.44 cu ft against a 146.0 L Vas.
03The watts that reach Xmax (in this enclosure)
Travel scales with the square root of power, so there is one wattage that puts the cone exactly on 19.0 mm — and a bigger one once a subsonic filter stops it wasting travel below the passband.
| Param | Value | Unit | Note |
|---|---|---|---|
| Fs | 21.70 | Hz | free-air resonance |
| Qts | 0.400 | MX15-22 | |
| Vas | 146.00 | L | equivalent compliance |
| Sd | 819.8 | cm² | effective piston area |
| Xmax | 19 | mm | one-way, as Dayton publish it |
| Pe | 800 | W | continuous RMS |
| SPL | 87.0 | dB | 1 W / 1 m, derived from T/S |
Driver parameters as published by Dayton Audio spec sheet. Curves computed against this enclosure’s actual net airspace.
Built From a Spec Sheet, Not a Sales Sheet
Every Proline X Performance Series enclosure is CNC-cut from Langboard Elite MDF, 3/4" (18mm) panels produced to published mill specifications. Most enclosure manufacturers source generic MDF without published data. We can tell you the internal bond rating, the modulus of elasticity, the modulus of rupture, and the face and edge screw holding strength for every panel in this enclosure, because we chose the material based on those numbers, not on price or availability.
Langboard Elite is produced in the United States. The specifications below are pulled directly from Langboard's published mill data and are verifiable. This is the same panel stock used in our full Proline X lineup.
Langboard Elite MDF: Published Mill Data
| Property | Value | Why It Matters |
|---|---|---|
| Panel Stock | Langboard Elite MDF | Named, verifiable panel source, not generic "high-density MDF" |
| Thickness | 3/4" (18mm) | Industry standard for subwoofer enclosures; panels below this flex under pressure |
| Density | 48.5 lbs/ft³ | Higher density = less porosity, better screw retention, reduced resonance |
| Internal Bond | 200 psi | Measures resistance to delamination under sustained internal pressure. The most enclosure-relevant spec on this sheet |
| Modulus of Rupture (MOR) | 4,200 psi | Bending strength before the panel breaks, relevant for larger unsupported baffle spans |
| Modulus of Elasticity (MOE) | 410,000 psi | Stiffness under load; higher MOE means less panel flex under bass pressure, less resonance |
| Face Screw Holding | 325 lbs | How firmly the panel surface holds a screw; critical for baffle joint integrity over time |
| Edge Screw Holding | 250 lbs | Panel edge retention, relevant for every joint that isn't face-to-face |
200 psi: The Number That Actually Matters for Enclosures
The internal bond rating measures how well the MDF panel resists delamination under sustained pressure applied perpendicular to the face. In a subwoofer enclosure, every bass transient generates a pressure pulse that pushes outward on every panel simultaneously. A panel that begins to delaminate internally loses stiffness gradually. The symptoms are slow: a box that starts to sound softer, less defined, less punchy over months of use. 200 psi internal bond is the spec that determines how long this enclosure holds its acoustic integrity under daily use at real power levels.
410,000 psi MOE: Less Flex, Less Resonance
The modulus of elasticity measures panel stiffness, its resistance to bending under load. A stiffer panel flexes less under the pressure generated by a high-excursion driver at volume. Panel flex is a source of acoustic coloration: the panel itself begins to radiate sound at its own resonant frequency, adding distortion to the output. 410,000 psi stiffness combined with V-groove and dado joinery means the panels stay rigid and the bracing controls resonance at the structure level, not the panel level. The bass you hear comes from the driver, not the box.
325 lb Face / 250 lb Edge: Joints That Stay Locked
Screw holding strength determines how firmly the panel grips a fastener at the face and at the edge. This matters most at the baffle joint, where the front panel meets the side panels and where the driver is mounted. A panel with low screw holding strength allows fasteners to loosen over time under vibration, leading to air gaps at the joint and loss of acoustic seal. 325 lb face screw holding strength means the baffle hardware stays put. Combined with dado joinery and adhesive, the front panel on a Proline X Performance Series enclosure is not going anywhere.
Named Panel Stock: Not "Premium MDF"
The phrase "premium MDF" or "high-density MDF" appears on marketing copy for enclosures across every price point, from $40 to $400. It is not a specification. It is a description with no defined standard. Langboard Elite is a named, sourced, mill-documented product with published data. We name it in our copy because naming it holds us accountable to the spec. You can look up Langboard Elite independently, verify the numbers on this page, and confirm you are getting what we say you are getting. That is the point.
Why Proline X?
Most enclosures are built to a price point. Proline X is built to a spec. Every box starts with published-data MDF, gets CNC-cut to exact internal volume, and is assembled by hand in our Tennessee facility. The difference shows up in the measurements, and in how the box holds up two years into daily use.
CNC-Cut to Spec
Panels are machine-cut on ShopSabre CNC routers and joined with V-groove and dado joinery. Consistent geometry, no hand-cut variance, no gaps at the joints.
Handcrafted in USA
Hand-assembled at our facility in Tullahoma, TN. Every enclosure is inspected before it ships.
Tuned to the Build
Internal volume and port geometry are calculated to spec and CNC-cut to exact dimensions. The box performs the same way every time.
Shop By Series








