Ground Zero
Ground Zero GZCA 1.5SPL-M2 1-channel competition SPL amplifier
SKU: GZCA 1.5SPL-M2
Ground Zero GZCA 1.5SPL-M2 1-channel competition SPL amplifier
What You Are Buying
A Ground Zero GZCA 1.5SPL-M2 from the Competition series: a 2 ohm stable, full-range Class D monoblock rated 1500 watts RMS, in a chassis that weighs 3.3 pounds. New and boxed. Made in Brazil.
Ground Zero is a discontinued line here. This is remaining stock and we are not restocking it.
Read This Before You Buy
Final sale. No returns, no exchanges and no warranty coverage. Audio Intensity is not an authorized Ground Zero dealer, so there is no manufacturer warranty path on this purchase. The amplifier is new, not used or refurbished.
The M1 and M2 Are Not the Same Amplifier
This is the part to get right before you wire anything. Ground Zero built two versions of this amplifier on one chassis, with one shared manual, and the only real difference is the load they are stable into.
| GZCA 1.5SPL-M1 | GZCA 1.5SPL-M2 (this one) | |
|---|---|---|
| Stable to | 1 ohm | 2 ohms |
| 1500 watts RMS at | 1 ohm | 2 ohms |
| 825 watts RMS at | 2 ohms | 4 ohms |
So the M2 wants a 2 ohm load, not a 1 ohm one. Check the end panel if you ever need to confirm which you have: it is silkscreened with the model number and the speaker terminal is marked SPEAKER OUTPUT 2 ohms.
What It Actually Makes
| 4 ohms, at 14.4 V | 825 watts RMS |
|---|---|
| 2 ohms, at 14.4 V | 1500 watts RMS |
| 2 ohms, at 12.6 V | 1200 watts RMS |
Ground Zero publishes that third figure and more manufacturers should. 14.4 volts is a running engine with a healthy charging system; 12.6 volts is a battery sitting on its own. The 300 watt gap between them is what your electrical system is worth on this amplifier, and it is the reason competition builds obsess over alternators.
It Runs Full Range, Not Just Bass
A three-position switch selects low pass, full range or mute. The low pass sweeps 50 Hz to 500 Hz, which is well above any subwoofer crossover point, and the high pass runs 5 Hz to 80 Hz. Frequency response is 10 Hz to 20 kHz within 3 dB.
That matters because it makes this amplifier useful twice. On a single subwoofer it is a 1500 watt monoblock. On a wall or a midbass array it will run the whole band, which is why Ground Zero positions it for SPL and SQL rather than bass alone.
Specifications
| Type | 2 ohm stable mono full-range Class D |
|---|---|
| Signal to noise | 99 dB at nominal power |
| THD+N | 0.1% at nominal power, 100 Hz |
| Damping factor | Greater than 1000 at 100 Hz |
| Low pass filter | 50 Hz to 500 Hz |
| High pass filter | 5 Hz to 80 Hz |
| Frequency response | 10 Hz to 20 kHz, plus or minus 3 dB |
| Bass boost | Up to 12 dB, variable center 35 Hz to 70 Hz |
| Input sensitivity | 500 mV to 8 V |
| Operating voltage | 9 V to 16 V |
| Fuse | 80 A, available separately and not included |
| Dimensions | 7.2 x 2.1 x 8.3 in (184 x 55 x 210 mm) |
| Weight | 3.3 lb (1.5 kg) |
| Protection | Temperature, short circuit, overload |
| Condition | New, closeout, final sale |
What Is Not On It
Worth stating plainly, because the Hydrogen amplifiers have these and this one does not.
- No fuse. The 80 amp fuse is a separate purchase and there is none on the chassis.
- No bass level remote, and no socket for one.
- No high-level input and no auto-on. You need an RCA signal and a real remote turn-on wire.
- No phase switch. Bass boost and the filters are the tuning you get.
None of that is a flaw on a competition amplifier. It is simply a different design brief: everything that is not making power has been left out, which is part of how 1500 watts fits in 3.3 pounds.
Electrical Requirements
- Battery current: Ground Zero asks for 80 amps minimum and recommends 160 amps.
- Power and ground: 4 AWG minimum, per the manual.
- Speaker wire: 13 AWG minimum. Remote wire: 20 AWG minimum.
- Fuse: 80 A, fitted at the battery within about 18 inches of the positive terminal.
- At 1500 watts you are asking a lot of the charging system. If the voltage sags, the amplifier gives you the 12.6 volt number rather than the 14.4 volt one.
Installation
- The side panels come off for wiring. Slide them vertically upward first, then pull them horizontally off the heatsink.
- Give the heatsink air. The whole chassis is the cooling system on an amplifier this small.
- Set input sensitivity to the head unit, not to taste. The range is wide, from 500 mV to 8 V.
- Use the bass boost sparingly. Twelve decibels is sixteen times the power, and the variable center frequency means you can place that lift exactly where your box already peaks, which is rarely what you want.
- Watch the CLIP LED. On a competition amplifier it is the most useful gauge on the chassis.
Who This Suits
Buy this if you are building to a 2 ohm final load; you want one amplifier that can run a sub today and midbass later; you have the electrical system to feed it; and you accept a final sale.
Look elsewhere if your build lands at 1 ohm, which is the M1's job; you want a bass remote or a high-level input; your charging system cannot hold voltage under load; or you need warranty coverage.
Condition and Sale Terms
Closeout stock from a discontinued Ground Zero line. New and boxed, sold as a final sale with no returns, no exchanges and no warranty coverage. Packaging may show shelf wear from storage. Specifications above come from the Ground Zero owner's manual for the GZCA 1.5SPL-M1 and M2 rather than from retailer listings. Once this one is gone the listing will be removed.
Questions on wiring, electrical requirements or whether the M1 or M2 suits your build: contact us.