Threaded Insert Kit | 8-32 and 10-24 Subwoofer Mounting Hardware
Threaded Insert Kit | 8-32 and 10-24 Subwoofer Mounting Hardware
The same mounting hardware that ships inside a Proline X enclosure when the subwoofer's maker does not publish its mounting hole locations, now sold on its own. Threaded inserts give the driver a real machine thread to bolt into instead of wood screws biting into MDF, so the subwoofer can come out and go back in as many times as you need without chewing out the baffle.
Which kit do I need
Two questions, in this order: what basket does your subwoofer have, and how thick is the baffle it bolts to.
- Stamped steel basket, take the 8-32. Pressed sheet steel frames are drilled for the smaller 8-32 thread. Its insert is 0.394 in, short enough to seat in a single 3/4 in baffle or a double one, so the 8-32 comes in one length and the baffle question does not apply.
- Cast basket, take the 10-24. Cast aluminum frames carry the larger 10-24 thread. Then pick by baffle: the Double Baffle kit's insert is 0.78 in, too long for a single 3/4 in panel, and the Single Baffle kit's is 0.512 in, which seats fully in one layer. Choose Double Baffle unless the panel your driver bolts to is one 3/4 in layer.
Not sure which basket you have? A cast frame is thick, heavy and rigid, with visible casting marks on the spokes. A stamped one is thin pressed steel and will flex if you squeeze it.
What is in the kit
Every kit ships the same way, and nothing else is needed to fit the driver: the bit that drills the hole, the drive that seats the insert, the tape that seals the flange and the key that tightens the bolt are all in the box. One kit covers one subwoofer, so a dual cabinet takes two.
- (8) E-Z LOK threaded inserts, hex drive with a flanged head
- (8) stainless steel socket head bolts, 1.5 in
- (1) drill bit, sized to the insert in that kit
- (1) insert install drive
- (1) hex key
- Woofer gasket tape, 48 in long, 1/4 in wide and 1/8 in thick
Specifications
- 8-32, stamped steel basket: 0.394 in inserts, 15/64 in drill bit
- 10-24, cast basket, double baffle: 0.78 in inserts, 9/32 in drill bit
- 10-24, cast basket, single baffle: 0.512 in inserts, 9/32 in drill bit
- Bolts: 1.5 in stainless steel socket head, the same in every kit
- Insert style: Hex drive, flanged, for wood and MDF
- Insert brand: E-Z LOK
- Gasket tape: 48 in of 1/4 in by 1/8 in tape, enough to go around any driver up to 15 in. Included for drivers that have no rubber gasket of their own
- Covers: One subwoofer, up to eight mounting holes
How to install
- Set the subwoofer on the baffle, square it up and mark every mounting hole.
- Drill the pilot holes with the bit in your kit: 15/64 in on the 8-32, 9/32 in on the 10-24. Run one into a scrap piece of the same material first to check the fit.
- Chuck the install drive into a drill or driver and run each insert in until its flange sits flush with the baffle face.
- Turn the subwoofer over and look at the back of its mounting flange. Many drivers come with a rubber gasket already fitted, and if yours does, skip this step. If the flange is bare, run the gasket tape around the back of it so it seals against the baffle. On a sealed box a leak there costs you output.
- Drop the subwoofer in and bolt it down with the hex key, snugging in a star pattern. Do not overtighten.
Which boxes need it
Any enclosure whose baffle is not already drilled and pressed. Where a subwoofer manufacturer publishes its mounting hole locations, we press the inserts into the baffle at the shop before the box ships and you will not need this kit. Where the maker publishes nothing, this kit is what lets you set the inserts exactly where that driver's own holes fall.